Question about Behringer Music
The stereo channels of my 1202 are MUCH quieter than the mono channels. It's almost impossible to get a setting that allows this to be more than a four-channel mixer. I've tried every combination of effects, gain, main volume, etc., to no availl Help!
It sounds as if the input is too low. what happens if you plug whatever is going into the stereo channels into a pair of mono channels. Or are you taking about the phono stereo tape input?
The stereo channels are line level whereas the other channels have both line and mic level inputs, what are you trying to put through the stereo channels? You must make sure the gain switch is set to the -10dB to get the most sensitivity (the mono channels have about -132dB max sensitivity BTW) You probably need a different mixer or possibly a submixer if you are needing more than 4 low level inputs.
Posted on May 16, 2014
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: I have the 2442 fx behringer
Check you assign buttons and bottom (three black square buttons) and play with them. It sounds as if you are not sending to that side. You should use mono cables into left and right. I set pan on left all the way left and right, all the way right. Hope this helps.
Posted on Jul 06, 2009
SOURCE: i have a behringer xenyx
Yep ! First thing is to eliminate any processing resource "hogs" that **** respources and can cause buffer overruns. Eliminate Antivirus, antispyware, and network communication and wireless network programs running in the background while recording.
Next make sure that ALL equipment is powered from the same receptacle or power source. In your case that should be the mixer and the PC.
Next remember that the condenser mic picks up everything... I have 5 of those mics and seemingly noise free environments turn out to have little things that generate fast rising pulses that you don't notice till they are recorded.
Lastly, the air here is very dry and plain old static electricity is rampart... Lady shuffling her feet was sending pulses through the mic cable at our church. They are NOT audible until they get into the sound system as clicks.
I have found that trying to record directely to a USB stick often has ooverruns and clicks... also burning a CD from stick to the CD results in noise due to buffer underuns. Burn from Hard drive to CD and make sure all the other hog programs are shut off.
Posted on Jan 04, 2011
SOURCE: Hope you guys can help... I
Yep! Get a decent audio interface that attaches to the PC with a USB connection and uses BALANCED lines to your mixer. I use a UA-25EX Roland/cakewalk as an example. (about $200 and there are cheaper units such as M-Audio Fast Track MKII ) Note these interfaces BOTH record and playback with two channels for stereo.
Essentially the audio board that is in PC's and Laptops are too near the switching noise of the processor and some of that is just bound to get into the audio lines as they don't even have balanced audio lines from the computers. Make sure you use either TRS or XLR balanced cables from whatever interface you get. Also connect ALL interconnected equipment to the same power source or receptacle. You can try to reduce the buzz with the mixer EQ's with what you have, but that sacrifices audio quality.
Posted on Mar 30, 2011
Assuming you're trying to power the monitors from this unit as well as the mains.....Confirm that the amp switch is in the middle position which splits the internal amps....one for main and one for monitors. Output A would power the monitors.... B would power the mains.
Posted on Aug 27, 2012
Tips for a great answer:
Jan 02, 2014 | Peavey SP5 2-Way PA Cabinet (800 Watts, 15...
Jul 10, 2011 | Behringer Xenyx 2222fx Premium 22 Input...
Mar 30, 2011 | Behringer XENYX 2442FX Mixer
Dec 27, 2010 | Behringer XENYX 2442FX Mixer
Nov 03, 2010 | Mackie 1202vlz3 12 Channel Mixer
Aug 05, 2010 | Behringer Xenyx 1002fx Mixer 10 Input 2...
Feb 05, 2010 | Mackie 1202vlz3 12 Channel Mixer
Jan 03, 2010 | Behringer Music
Jul 06, 2009 | Music
Mar 22, 2009 | Behringer Xenyx 1002fx Mixer 10 Input 2...
73 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: