Question about Garden

1 Answer

I have a 1999 Murray riding mower just changed the drive belt. Mower won't go unless I'm holding clutch in. Help

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

YOU Have the belt on wrong remove and try again its probably on the wrong side of the tensioner that is connected to the pedal

Posted on May 06, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 24 Answers

SOURCE: murray riding lawnmower motion belt routing

I need your model # took look it up , I am a Murray dealer.
The thing to rember there are two kinds of idler pulleys flat idlers that ride on the back side of belts and v pulleys that ride inside the belt . wont be back to the shop until the feb 10.
good luck

Posted on Feb 08, 2009

mowerman1857
  • 389 Answers

SOURCE: how to adjust the mower deck on my murray rider,

Park the tractor on a firm, level surface. . .
At the lower end of the lift/lower travel slot, there should be a plastic cover which you pop up so that your blade lift handle goes all the way down (it should say something about blade level on there somewhere. . . . .
After you have the handle in this position, look at the front lift arms of the mower deck and find the 2 large wing nuts, one on each side. . . . .
Loosen these while the deck is down and then retighten them Your deck is now level and will lift to its highest recommended position when you raise the lever

Posted on Oct 11, 2009

  • 202 Answers

SOURCE: can't figuire out how the belt goes on need murray

You should be able to get your info here:


http://www.outdoordistributors.com/pdf/Murray/MURRAY-MODEL-42910X92A-LAWN-TRACTOR-%281996%29-PARTS-LIST.pdf

Posted on Oct 25, 2009

  • 15 Answers

SOURCE: Murray Mower Manuals

Try the Murray mower website.

Posted on Apr 19, 2010

mickey813
  • 472 Answers

SOURCE: belt drive diagram for a murray riding lawn mower

0050c10.pnghope this helps ya

Posted on May 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why murray riding mower wont crank when being jumped off


Some mowers have safety switches that unless you are sitting on the seat and the clutch pushed in they will not start. Not sure if this is the answer.

Jan 05, 2017 | Murray Garden

1 Answer

Will an older 42 inch murray riding lawn mower deck interchange with an older rally riding lawn mower deck ?


Mower decks are very specific to the tractor. Unless it was the same manufactured mower, and just branded differently, then not likely! Belts are your next problem as even an inch longer or shorter will cause problems.

May 07, 2016 | Murray Garden

2 Answers

How to repair clutch on Murray riding lawn mower 465306X8B


465306X8B - Exploded drive belt parts view.
repair-clutch-murray-riding-lawn-mower-yf3zdllwco2f1yp5d1drasa2-2-2.png

Jun 26, 2015 | Murray Garden

1 Answer

30" Murray riding mower drive belt diagram


Here's a link to your belt diagram,just click on picture to in large. motion drive belt came off 10 hp 30 deck mower Murray Riding Mower

Aug 21, 2014 | Garden

1 Answer

My murray riding mower wont go in to gear ???


If you can select gears when the motors not running but not when it is then your drive belt is dragging.(trying to drive even when the clutch down).This is usually the belt guides not holding the belt in a neat loop off the pulleys front and back when the clutch is down.

Jan 31, 2012 | Murray Garden

2 Answers

The mower deck drive belt slipped off the idler pulley on my 42'' Murray riding mower deck because the idler pulley was worn out. I need to know how to loop the belt back around the pulleys after I replace...


Get the model number off the tractor, go to:

www.murray.com

enter the model number and you will find a manual with pictures of how to route the belts along with a lot of other good information

Sep 30, 2009 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2475 Answers

john h

Level 3 Expert

11122 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you a Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...