Question about Audio Players & Recorders

1 Answer

Sound from one speaker only.

Help. I have a Technics SU-X501 amplifier in black and I only get sound from one speaker. When I connect each of the two speakers individually,I have sound from each individual speaker,but when both are connected up just one speaker works. Through headphones,it sounds like both speakers are working.
When both speakers are connected and I move the balance from left to right,again just one speaker will take over (could be either speaker).
I have followed 'Big Reds' instructions,but still no joy. Please help...single mum.

Posted by on

  • billger Dec 04, 2007

    Same problem. Only one speaker works at a time. In addition the dial lights on the amplifier do not illuminate.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 682 Answers

Your output stage had a problem in electronic output device and must be maintained in service center.

Posted on Mar 11, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Su-x501 turning off intermitently

If your unit is intermittent, check the speaker wires on the back of the amplifier for stray threads of wire, next! the printed circuit board underneath should be checked for bad or cracked solder joints, finally one more parts are defective, tough problem to nail down, recommend technician.

Jul 08, 2012 | Technics Audio Players & Recorders

1 Answer

Speakers for Technics SU X933?

check given link for speakers

Jun 05, 2012 | Technics SU-G75 Amplifier

1 Answer

Hi I just got a Technics SU V2 amp and can't get sound from the speakers. What size speakers would suit this amp? What is the correct method to connect the speaker leads to the back of this amp,...

Being a 500W amplifier, you need to connect speakers with 300W each. The correct method to connect speakers is red terminal of speaker should be connected to red terminal of amplifier & black to black. The left side to left side speaker & right to right speaker. There may be main & remote terminals. Main speakers are the speakers at local place of the amplifier & remote for remotely placed speakers. I do have Technics SU-V85A which is somewhat similar. Enjoy! A nice piece to listen.

Oct 22, 2011 | Technics SUV500 2-Channel Amplifier

1 Answer

I want to no how to wire the hole system up just picture diagram SU-X501

This appears to be a tough one to find for free. There is some info out there - but it will cost a few bucks. The service manual or sometimes called a "shop manual" is for those that work on damaged units - and is probably over the top for your needs. The operating manual or owner's manual is likely the same as the one that came with the unit when new. Either can be had at the site below for $15 and $10 respectively:

I am not affiliated with this or any other site that charges for manuals, tips, advice, etc.; and only offer it as a source for the info you're looking for. I hope this helps!

Jun 11, 2010 | Technics SUV500 2-Channel Amplifier

1 Answer

Technics SU-G95 Amplifier and no sound on left speakers

Usually this is a defect in the output amp IC. If you have no experience with repairs of these types of units, have it checked by a service shop. If the output AMP IChas failed, it will cost about $75 for a replacement. This unit uses an RSN3306P IC .


Mar 14, 2010 | Technics Audio Players & Recorders

1 Answer

Technics su-Z750 Intergrated Amplifier stays in Standby

This happens when one or more components in the power amplifier section has failed.

The protect circuit keeps large DC voltages off the speakers.

The only thing you can check for before finding a tech is that the speakers are firmly connected at both ends. If they are ok, you need a tech

PLease rate my help if this helps

Nov 05, 2009 | Technics Audio Players & Recorders

1 Answer

Need to replace my Technics SU-X501 Amplifier.....HELP!!!!

its better to buy desame brand of your unit for compatibility sake...

Jun 19, 2008 | Audio Players & Recorders

1 Answer

Channel has switched off.

Make shure speaker wires are not crossed at amp or at speaker terminals. Check balance control is at center. Check sound with headphones to see if final amp to speakers is the problem. Try switching imputs on back panel from right to left see if same speaker is on,.Try all loudness controls and tape dubbing buttons to see if any are dirty.
Good Luck

Nov 03, 2007 | Audio Players & Recorders

Not finding what you are looking for?
Audio Players & Recorders Logo

Related Topics:

758 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audio Players & Recorders Experts


Level 3 Expert

102366 Answers


Level 3 Expert

5318 Answers

The Knight
The Knight

Level 3 Expert

74999 Answers

Are you an Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides