Question about Raypak RP2100 DIGITAL POOL HEATER R265

1 Answer

I've replaced 010253f 3 times now and there is no display on it again what the problem with this part.

Heater is P-R405A-En

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 305 Answers

Make sure your getting 24volts to display screen. if you are not, then problem is from elsewhere

Posted on May 10, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does pool heater read SPK and won't light?


Sounds like your ignitor is shot. You may have to replace it.

Jul 24, 2014 | Rheem Water Heaters

2 Answers

Faulty O2 sensor heater


heater is part of the 02 sensor. Replace sensor

Feb 03, 2013 | Cars & Trucks

1 Answer

Raypak p-r405a PRS message. tried adjusting pressure switch, no change


clean out pump basket, backwash filter for starters. jump the pressure switch if nothing changes. if burners fire then replace the pressure switch

Dec 06, 2012 | Raypak Pool & Spa

2 Answers

The code CE is showing on my Hayward pool Heater what does that mean and can I fix it


I have just repaired my H400 series pool heater from the 3rd CE error in only 3 years since the pool and heater were installed. In each case the circuit board (F0059-456600) was in some way to blame .... I will explain.
Case 1 : Only months after installation the CE error came up. Rain water had got in around the display module and water-damaged the circuit board. It was replaced under warranty. Since then I keep a big plastic lid covering the display unit when the heater is not in use.
Case 2 : 1 year from new the CE error came back. On investigation it was found that a rat had managed to get inside the heater (there are big gaps around the pipe entries) - it had then partly chewed through the ribbon cable joining the two circuit boards together. Display circuit board was replaced at my cost - and all was well again. I also rat-proofed the heater - eliminating all the big openings with chicken wire.
Case 3 : Fired up the pool heater for the first time this year and CE came up. I pulled the display module and this time found obvious signs of blackening / burning on the display circuit board under the big green resistor (R1). Luckily I had kept the old circuit board from the previous time and was able to make 1 good board from the two I had - back in action now.
So in my experience it has been the display circuit board each time - and it only takes a phillips-head screwdriver and about 10 minutes to get it out.

Jul 27, 2011 | Hayward 250kbtu Ng Pool Heater - Inground

1 Answer

I need a new motherboard for a 206A heater. Where do I go?


I assume it's a Raypak 206A? When you're talking about motherboard, do you mean item 4-C (P. C. Board/Control IID Units) ? then it's part number 010253F You can download a manual with parts list from www.raypak.com
You can also order parts from them as well email them for questions. Are you sure your P.C. board is bad? If so what caused it?

Jun 30, 2010 | Pool & Spa

1 Answer

Have a 010253F replcement kit for a Raypak model 335a heater. Need wiring instructions.


Go to the RayPak web site. They have a pdf of the instructions for replacing the board with what you have.

Sep 04, 2009 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

Bad LCD = Bad PC Board unfortunately...


check grounds to board also check transformer for voltage look for blown fuses

Jun 22, 2009 | Raypak Rp2100 Pool & Spa Heater Lonox 407k...

1 Answer

I have a raypak p-r405a pool heater. When i hit the mode button to turn on heater this morning, previous thermastat setting automatically dropped to 64 degrees (which is the current water temp) and now i...


Some raypaks have a remote setting. I cannot remember the exact keys to hold to change it but i think that you hold both the up and down arrows for like 10 seconds. The instructions on the particular heater that i was working with were right on the display panel, but if its not there it will be in your owners manual.

Apr 04, 2009 | Raypak Free Hydraulic Lift Gate Delivery -...

Not finding what you are looking for?
Raypak RP2100 DIGITAL POOL HEATER R265 Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Raypak Pool & Spa Experts

Bill Jordan

Level 2 Expert

372 Answers

paulcarew

Level 3 Expert

2458 Answers

Brad Brown

Level 3 Expert

15478 Answers

Are you a Raypak Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...