Question about Proform 730 Folding Treadmill Model PFTL71104 - !

Open Question

Proform 730 pops breaker

During a 25 minute couch to 5k...the breaker popped 3 times. Kept in a cooler room of the house....what's causing this?

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1751 Answers

SOURCE: I have the proform 785 ss treadmill and it shus

Unlpug it for 30 minutes to reset it

Posted on Nov 26, 2010

Ad
ercupa190
  • 12223 Answers

SOURCE: the breaker keeps tripping halffway through my workout on my proform 730 cs. why?

see my personall TIPS for to see the schematic.
2) Try to run the software calibration for diagnose and troubleshooting and fix it.
3) The c. breaker can indicate the motor, trafo, capacitor, or board is hot and trip the breaker.

sincerely. God bless you

Posted on May 03, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Compressor builds to 100 lb pressure. after a few minutes use, it comes on again to begin pressure build up. next cycle, it trips circuit breaker in house.


You didn't provide all pertinent info available to you. Lets take what we have; and, consider why your compressor is overloading the circuit breaker. Points to ponder:

  1. Not knowing the exact model (not series) I don't know what the amperage pull is for your "extreme" compressor or the circuit breaker's rating. A 25 amp compressor connected to a 25 amp breaker could be an issue. Campbell Hausfeld's support pages are crashing so I can't check the possabilites.

  2. Are you using a lightweight extension cord? The lower the rating of an extension cord the higher the amp pull on the breaker. If you eliminate the extension cord does the problem go away? Ohm's Law applies. <http://www.ohmslawcalculator.com/ohms-law-calculator>

  3. What else is on this breaker? Is there other high-amp equipment in another room (water cooler, window air-conditioner, portable electric heater, etc.) pulling from this same circuit breaker.

  4. Is the circuit breaker not performing to specification? I've seen failing breakers trip early.

    First, check the owner's manual for power requirements. Next step, use no extension cord; and, insure nothing else is pulling power on that breaker. Then, use a different breaker and see if the problem follows the compressor. If all else checks out than I'd consider binding in the compressor causing the amp pull to be too high.

    Good Luck!

Mar 29, 2015 | Campbell Hausfeld Extreme Contractor...

2 Answers

Dish machine keep popping breaker


your heating element is perhaps gone its the most likely things just after inital cycle call.... try to disconnect the element two spades and if it goes past this point i would replace it for sure
or some leakage too earth
sounds like too me the element jacket is bad and water has leaked in good old house trip before your house may have burned down...!!!! so...

something is leaking to earth ... that has water inside
perhaps the main recycle or outlet pump housings has cracked...??? look for rust on the motors laminated cores...

Mar 05, 2015 | Washing Machines

1 Answer

Pool pump turned off when turned back on popped and smoked


Ouch! Never run a pump that is leaking badly. It sounds like the seal or the housing gasket didn't set right when the motor was changed out.
The short story is you need to replace the motor again. The thermal overload and the breaker kept your house from catching on fire. Get qualified help to install next time. People consistently underestimate the amount of damage that pool equipment can cause when not done correctly. Better luck with the next one!

Jul 03, 2013 | Pool & Spa

1 Answer

The breaker keeps tripping halffway through my workout on my proform 730 cs. why?


see my personall TIPS for to see the schematic.
2) Try to run the software calibration for diagnose and troubleshooting and fix it.
3) The c. breaker can indicate the motor, trafo, capacitor, or board is hot and trip the breaker.

sincerely. God bless you

Apr 28, 2012 | Proform 730 Folding Treadmill Model...

1 Answer

I have proform 730 and I can't get the power to turn on.


Dear Sir:

1( You have to use some VOM for to measure voltage, continuity.
1a( Test the outlet wall with some bulb
2a( Reset the c. breaker from your house.
2( Test the power cord , for loose cable, or broken cable.
3( Test the power switch, if is open or short.
4( Reset the c. breaker in your machine.
5( If the machine is Not working maybe you have the power supplies, or fuse or main motor board faulty. Test it.

See my personal TIPS for HELP.

sincerely. God bless you.

ernesto cuadra
managua, nicaragua. c.a

Mar 13, 2012 | Proform 730 Folding Treadmill Model...

1 Answer

What causes a Model 730 cs is quite noisy during operation?


Check rear roller, bearings might be worn.I had to replace mine.

Feb 12, 2011 | Proform 730 Folding Treadmill Model...

1 Answer

My SM11 model Steamist was installed above our shower/steam room. It is 2 years old. While in use recently, it made a loud sound like a low-pitch popping sound or low boom. Imagine somebody inside a...


The heating elements had burned up in the unit therefor creating a dead short on that circuit. Main breakers on homes and buildings are VERY sensitive and will sometimes trip before the smaller branch cicuit breakers will . So the popping you heard was the heating elements breaking down inside the unit it can be some what noisy.

Nov 03, 2010 | Steamist 1100 Sm11 Large Capacity Steam...

1 Answer

Hitachi RAS09UH randomly pops 15A circuit breaker


Two things that you could check: 1) If you have access to an ampmeter, determine if the unit is drawing over over 14 or 15 amps, 2) replace the suspect circuit breaker in case it is beginning to go bad. Breakers only trip for overcurrent conditions or failure of the breaker itself. If it is pulling close to 15 amps, then it could heat up over time and trip.

Jul 09, 2009 | Hitachi RAS-09UH Air Conditioner

2 Answers

Blown breaker


It sound like all of those go through your bathroom GFCI. I would recommend moving your outdoor circuit breaker indoors if possible or enclosing it to make it water-proof. You may also do some rewiring from your main breaker box ( if you are handy) to eliminate the outdoor box completely considering you have 100 amp / 200 amp breaker box inside your house. If you still have an old FUSE BOX with 60 amp service, I would recommend replacing it with a 100 amp or 200 amp breaker box depending on the size of your house. I would separate the laundry room by itself with 12/2 gauge wire with ground on a 20 amp breaker. You can then take your bathroom (using 12/2 gauge wire with ground keeping your gfci ) and run it to another breaker in the house with a 20 amp breaker or add a new one if there is room in your main box. Now all you have left is the porch light. You can run that separate from everything to your main breaker box using 14/2 gauge with ground to a breaker in your main box by adding a new 15 amp breaker or adding it to another 15 amp breaker that does not have a very high load such as a bedroom. In general Kitchens, Bathrooms, Laundry rooms should be on there own separate 20 amp breakers. Most every other room can be 14/2 with ground on a 15 amp breaker... hope this helps....Joe

Dec 17, 2008 | Prime 10 Amp Circuit Breaker

1 Answer

Ewave kot-131UB pops breaker


Yes, this is caused by either a bad door switch or a loose door or loose door switch mount.

Even though a door switch clicks, it may still be bad inside. Its continuity must be checked.

Door switch or mount trouble can be caused by slamming the door or by opening the door while it's cooking without hitting the Stop pad first.

If you someone you know decide to look into it, we have critical information on safety, disassembly and door switches at our site, and our link is at our listing here on FixYa: http://tinyurl.com/yzjozk

We're happy to help and we appreciate your thoughtful rating of our answer.

Mar 13, 2008 | Kenmore 80412 Microwave Oven

Not finding what you are looking for?
Proform 730 Folding Treadmill Model PFTL71104 - ! Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Proform Exercise & Fitness Experts

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

128 Answers

Matt Olenzek
Matt Olenzek

Level 2 Expert

293 Answers

Electro Med Services...
Electro Med Services...

Level 3 Expert

6694 Answers

Are you a Proform Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...