Question about Magnum DeltaForce CB Radio

Open Question

How to wre a 6 pin din connector to midland 13-883b cb radio?

Cannot find what pins go to where

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 204 Answers

SOURCE: Omegaforce s45 mic wiring

1-Shield - Ground
2-White - Audio
3-Brown - Transmit
4-Green - Receive

Does this color code look like what you have in your mic?? sorry for the delay,,, Mechanic

Posted on Nov 05, 2008

  • 170 Answers

SOURCE: Diesel #8-32 echo power mics

cobra 4 pin is pin1= shield, pin2= mic audio (usually the shield is wrapped around the mic audio wire).pin 3= transmit or push to talk usually red or white whichever isnt wrapped with the shield, and pin4 = receive or speaker complete

5 pin cobra=1-Audio 2- Shield 3-Receive 4-Switching Wire 5-Transmit, you can jump pins 4 and two

Posted on Dec 28, 2008

SOURCE: i need a 4 pin mike wiering for a rca cb radio

look up rca mic wirering schematics on the web theres lots out there

Posted on Oct 17, 2009

  • 141 Answers

SOURCE: Need Wiring for Magnum omegaforce for RK56 this

RoadKing 56 to Omegaforce:
Pin 1 : Microphone Audio -white
Pin 2 : Receive-black
Pin 3 : Transmit-blue
Pin 4 : Down (Up w/ 22K Ohm Resistor)- no connect
Pin 5 : Ground-shield & red
Pin 6 : +13.8 VDC-no connect

Posted on Jan 30, 2010

  • 500 Answers

SOURCE: trying to put a 6 pin plug on to a base mic a

Just check the wires on the mic switch. That will give you the right colors. This works with any mic. And any radio

Posted on May 16, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need manual for midland 76-858

here is the pin outs.. look at the switch in the mic handheld housing.. and attach as the one shown for midland 4 pin. this will work with any radio. and doesn't matter which color is what.. as long as the wire on the switch matches the wire on the pin correctly.

Aug 01, 2014 | Midland 1001Z 40-Channels Base CB Radio

1 Answer

Need pin out for trc 432 cb radio

its a 5 pin din connector.All radio shack radios with the din plug are 5 pin

Dec 08, 2013 | Radio Shack Radio Communications

2 Answers

I have a Midland CB Car with no mike or a car power pluge, the model # is 70 - 336B and the serial # is 760408

Your midland CB will use a standard 4 pin wired CB plug which is most common for most mics sold today. Your power cord will be a standard 3 pin CB power cord which again is most common with CB's today. You need not purchase a "radio specific" cord or mic. Cobra, Uniden, Midland all the same mic pin out and power cords. Good luck.

Feb 09, 2011 | Radio Communications

2 Answers

Need a mic for a midland 79-892 SSB Radio or at least the 6 pin mic plug

Because the radio has controls for the clarifier on the mic, there is an extra wire to have the control in the mic. This is why the radio uses a six pin mic but it is an offset pin spacing. This is an extremely tough mic connector to find and the radio is getting pretty old.
I have on several radios strapped the RF gain and used this knob as the clarifier and installed a five pin mic connector in the radio and it's mate on the mic. Not a job for those who are not used to doing this! But the radio is worth the repair as it is a good one! Email me at....

Feb 12, 2010 | Midland Radio Communications

1 Answer


Uniden 2-way radios have 5 pin mic connectors, mind you pin 1 is not used (12V), are you sure both are uniden radios? what are the model numbers?

Jul 24, 2009 | Midland 1001Z 40-Channels Base CB Radio

1 Answer

Converting a different brand of mic for a midland CB

This should be a typical Midland pinout. If you are using a generic 4 pin mic that is wired to cobra/Uniden, all you have to do is switch pin 1 & 2, then 3 & 4.

Not all mics are color coded the same with their wires.

Oct 06, 2008 | Midland 1001Z 40-Channels Base CB Radio

1 Answer

Wiring a midland 78/999 cb radio microphone

Pin 1 = white
Pin 2 = shield
Pin 3 = black
Pin 4 = red

Sep 27, 2008 | Midland 1001Z 40-Channels Base CB Radio

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Magnum Radio Communications Experts

Level 2 Expert

500 Answers

Brad Brown

Level 3 Expert

16195 Answers

John Porter

Level 2 Expert

85 Answers

Are you a Magnum Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides