Question about Intex Surf N Slide

Open Question

Are there any instructions? How do you inflate or fill the bottom part that raises it off the ground for the top of the slide

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sunbeam steam valet instructions


How to fill your Sunbeam Steam Valet
Here is how you fill your Steam Valet. Press the small button on the back of the handle and pull bottom of handle apart from the top half of steam valet. Then take off the white cap on the inside of the handle and fill with water to top. Place cap back onto the opening and slide handle back and click in place. Plug in and you're ready to steam within a few minutes. If it spits out water let heat up a little longer if that doesn't stop it then tie a thin cloth over the top part where steam comes out to keep the water from spitting out onto your fabric. Hope these instructions are clear enough. More questions about this iron go to www.manualslib.com.

Feb 29, 2012 | Sunbeam Irons

1 Answer

Want to blow air out to inflate mattress


You need to remove the main head with the brushes from the front and install the safety cup. The remove the bag by unclipping from the top and disconnecting the boot end from the bottom with an outwards twist. Now attach the hose to the exposed outlet; attached the thin nozzel designed for inflating to the hose and switch on - you will feel air being expelled from the hose.
Air, which normally contains dirt and dust because you're hoovering is blown into the bag, but now with the bag removed; the air is blown into your hose, through the attachment and into what ever needs inflating.

For a good visual set of instructions click on the following link and scroll down to the second set of instructions :
How to change hoover to a blower

Sep 25, 2010 | Kirby G5 Bagged Upright Vacuum

1 Answer

Washing machine spin cycle not working properly


Its the belt. Easy fix. Lift the top by sticking a screwdriver into the gap between the front panel and top panel. There are two "tabs" you need to push in while lifting the top front up. Then raise the front up a bit off the ground with blocks to take out the two phillips screws near the bottom (front). Then slide the front panel down. The belt is on the bottom. simple to remove from below the pully. not sure the belt type to replace with.

Feb 21, 2010 | Washing Machines

1 Answer

How to fill the covertible fluid?


hi friend,

On top of one end of the convertible top pump is a rubber fill plug, remove it and fill it to the bottom of the fill hole. Here is the proper procedure.
Rotate and raise the motor/pump assembly so the reservoir is in the up position. The rubber filler plug will be at the top. Raise the motor and pump fitting to at least 2" above the horizontal rear seat back reinforcement. Tilt the motor and pump assembly to approximately the 10 o'clock position, with the rubber filler plug still at the top. CAUTION: The motor and pump assembly must remain in the current position until the rubber filler plug is reinstalled in step 7. Remove the rubber fill plug from the reservoir. Fill the hydraulic system by adding Dex ron 2 Automatic Transmission Fluid to the bottom of the fill hole. CAUTION: Do not operate the top switch in the "up", closing the top, direction. With two people, activate the top switch in the "down" (opening the top) position to fully retract the cylinder rods and hold for approximately 5 seconds, until the motor and pump stalls. A percolating or gurgle sound/feeling is an indication that the procedure is working. Top off the pump with Dex ron 2 and insert the filler plug.

thank u for using fix ya

regards,
sivaranjini

Aug 06, 2009 | 1998 BMW 3 Series

1 Answer

How do i fill forks on a 1980 cb 900 honda


Look for a small drain screw of at the bottom of each fork,this is where you drain it,Then there should be a large hex at the top where you add the correct mount,also the spring is in there so have the front end raised off the ground by setting the frame up on some blocks

Jul 18, 2009 | 1995 Suzuki GS 500 E

1 Answer

Do i fill forks raised or on ground?


If you are replacing the oil the fork tubes should be removed. If you are just topping off the existing oil then just raise and fill.

May 19, 2009 | 1995 Honda CBR 900 RR Fireblade

1 Answer

Washer won't spin


press in clips each corner with putty knife and lift top remove screws bottom front panel slide panel down and off ..locate pump. turn washer to spin and switch on if faint hum felt at pump more than likely plugged with something if pump is running fine ck for something in drain lines..most washers i would say lid switch but on those i believe if switch was bad wouldn't aditate either ck by raising lid ..if agitates with lid raised ck lid switch if not switch ok

Sep 13, 2008 | Westinghouse WWS833ES Super Capacity Top...

1 Answer

The top shelf of my dishwasher will not stay closed if I am loading the bottom. It just slides out.


The machine may be out of level (tipping forward). Remove bottom toe panel and try raising the front two leveling feet. Also make sure the top of the machine is secured properly to the counter top or cabinet sides.

Jun 22, 2008 | KitchenAid Dishwashers

2 Answers

Kenmore Series 80 won't stop filling.


Kenmore washers
Fill switch
pull off fill knob
remove plastic trims from front face ends of control panel exposing screws
remove phillips head screws from bottom
slide control panel forward & up ~1inch then flip over backwards on top hinges
to remove fill switch
depress lock tab right side where switch body touches back of control plate
rotate counter clockwishe 45-90 deg
withdraw fill switch
remove plastic tube from switch body
Blow any water out, should be empty when washer is empty messes up pressure sensing
refit plastic tube
adjustment screw is 1/8" hex head bolt next to knob shaft
clockwise raise water level
counter clockwise lower water level
can be operated in this open position to check operation, may have to move switch between fill positions to restart fill operation

Nov 27, 2006 | Kenmore 15864/15862 Top Load Washer

Not finding what you are looking for?
Intex Surf N Slide Logo

Related Topics:

569 people viewed this question

Ask a Question

Usually answered in minutes!

Top Intex Water Sport Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Tom Chichester

Level 3 Expert

33250 Answers

Bill Boyd

Level 3 Expert

40663 Answers

Are you an Intex Water Sport Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...