Question about Singer 7442 Mechanical Sewing Machine

1 Answer

How do i put bobbin inand were do i put yhe threed

I need help i just need instuctions

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 208 Answers

The bobbin should fit under the steel plate you'll have to make the needle stay up to remove the base plate

Posted on Jun 21, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Hi im trying to fig out how to run this pw201. the instruc. r a little hard to get. is their an easy way to explain how to thread and bobbin thread this machine

Electronic sewing machines have a sensor that knows when you are winding. Just place the bobbin on the spindle and push it over until it locks for bobbin rewind. Place thread through one of the holes and allow the bobbin to turn. Now step on the gas and let it fill up.

Take your bobbin carrier out. Place bobbin in carrier so the thread is unwinding, counter clockwise usually. Place the thread under the little slit and pull it until it feels like it is under a pressure. To check for this pressure (tension) hold the thread carrier with thread under tension and gently bob. It should allow a small amount of thread to extend. If not then loosen the screw. If too much extends then tighten. Now, place the carrier and bobbin in the sewing machine and make sure the snap is heard when you place it in there. It has to be seated. I believe this is a electronic machine and you won\'t have anymore problems because it will do the rest of your needed things before you sew. HOPE IT HELPS

Apr 26, 2014 | Sewing Machines

1 Answer

My threed will not come up from the bobbion

Manually feed the bobbin thread through the needle top plate and try sewing. The result might give you a further clue as to what's going on. If its not something as obvious as excessive tension or incorrect routing of the bobbin thread, it might be the clearance between the needle and the needle hook. Did you try changing needles in case it's a bent needle?

Jan 23, 2013 | Husqvarna Sewing Machines

1 Answer


I'm not sure what you mean about this. When you want to wind a bobbin, you put it on the bobbin winder pin on the upper right side of the front of the machine, and then push/slide it down towards the bottom of the machine; it goes about an inch or so, and then the screen will say "bobbin winder engaged." The bobbin is now in line with the fat lever that will automatically stop the winding when the bobbin is full. (I usually use my fingernail to guide the thread up and down a bit so that the bobbin is wound smoother.) If you have the same manual I have, that came with my machine about 4-5 years ago, the two pictures on the bottom right-hand side of page 10 will show you what I mean. -- BTW you can wind a bobbin with the machine threaded or not threaded. (pages 10-11) Also, always be sure to wind the bobbin with the logo-marked side up, the same way you place it in the bobbin holder when you are ready to sew. -- I hope this helps.

Jan 26, 2011 | Husqvarna Designer I

1 Answer

How do i put threed into the bobbin and keep it from not getting tangled?

Is it getting tangled while you're spooling the bobbin on the top right corner of the Singer 1507 machine? If this is the case, you have to pull the thread through the top tiny hole in the bobbin, and hold on to the thread end. Then click the bobbin to the right to lock it in place, power up your machine. Keep holding the thread as you begin spooling the bobbin. Let go of the thread once the bobbin starts to spin a few rounds and the thread should not get tangled.

Sep 29, 2010 | Singer 1507

1 Answer

I have a Euro Pro model 9106 sewing machine and I need a replacement bobbin cover for it, do you know where I order one

Ihave a Euro PrO 9106, I just ordered that part. They are in Canada yhe phone number is 1-800- 798- 7395 follow the prompt.

Gloria 5-25-10

Jan 25, 2010 | Sewing Machines

2 Answers

Pfaff Expression 3.0 works great in the shop, but when I get it home the bobbin thread doesn't engage with the needle thread. The needle thread ends up making large irregular loops on the bottom of the...

pfaff expression 2.0 works the same. I spend lots of hours with the thread tension and it don;t give me a good stitch. the needle threed ends up making large irregular loops .

Apr 12, 2009 | White Sewing 1521

1 Answer

Unable to wind bobin og CS6000 Brother sewng machine

I have the same machine and this is how I do it. If this doesn't work, then it must have a problem and not because you have done it incorrectly.

Thread the main thread on machine as shown.
Pull the end of the thread throw the top hole in the bobbin roll ( you know the little clear thing where the bobbin thread will be wind on.
Place it on the bobbin holder and push that unit to the right to touch the thing there on the right....Now turn on your machine. Either by using the sew button or using the foot pedal.
This should work...

Good luck.

Feb 06, 2009 | Brother CS-6000

1 Answer

Brother VX-1120- The needle is not picking up bobbin thread.

I had the same problem with my brother vx-1120 sewing machine. I set the needle to lowest position by using the hand crank. Then I loosened the knerled set screw that holds needle in place. Then I moved needle shaft till the eye of needle is just lower than the hook on the shuttle loop maker. It made my mechine work. There are instuctions for ajusting timing on machine but I think these mechines are built to not fix and throw out. Just because there where no ajustment marks at all on machine, any machanical machine will needed to be ajusted sometime.

Jul 08, 2008 | Brother CS-8150 Computerized Sewing...

1 Answer

Bobbin/raceway and timing problem; Necchi 3577

ok.....without the bobbin case in and a fresh needle in, turn the machine to the side and turn the crank wheel counter clockwise, the hook of the machine should bypass the cusp of the needle, thats the part of needle that is by the eye and curves in alittle, if it is not the timing is off, try to adjust this by adjusting the needle bar, this is not a easy easy repair but takes patients, im assuming that, thats where it was thrown off timing

Jan 21, 2008 | Necchi 3537 Mechanical Sewing Machine

Not finding what you are looking for?
Singer 7442 Mechanical Sewing Machine Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Singer Sewing Machines Experts

Tally Girl
Tally Girl

Level 3 Expert

1125 Answers

Cindy Wells

Level 3 Expert

5124 Answers


Level 1 Expert

41 Answers

Are you a Singer Sewing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides