Question about Zanussi F1245W Front Load Washer

1 Answer

Need to replace water pump. How do I get old one out and new one in?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Follow your waste pipe and there will be 3 screws or it will turn to the left afteryou have moved the little clip

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Metal pipe on water pump will not stop leaking.new water pump and new metal pipe


Did you replace old rubber O ring before reinstalling tube back in position ?

Mar 14, 2014 | 2000 Ford Windstar

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

Replacing water pump


To replace water pump on Chevrolet s-10. You need take of the top half of the fan shroud, pop off the hoses to the water pump and the take out the bolts to the water pump.To get the fan off, you need a special tool called a half h tool, The half H tool holds the bolts in place so you have leverage to then twist the fan off.Before removing parts to replace water pump first drain the antifreeze.Place the drain pan under the radiator, open the drain on the bottom of the radiator and allow the antifreeze to drain into the pan.Remove the upper fan shroud using a 10-mm socket. Remove the four 13-mm nuts securing the radiator fan to the water pump pulley, using a wrench.Pull the water pump pulley off the water pump. Remove all hoses from the water pump, including the lower radiator hose and upper heater hoses. Remove the four bolts securing the water pump to the block, using a 15-mm socket and ratchet with the 3-inch extension. lift the water pump off the block. Clean all the remaining gasket material off the block passages using the gasket scraper. Lay the new water pump face down with the outlet ports up.And complete the procedure of fitting the new water pump in reverse of how you removed the old one.---------------- Thank you.

Jan 24, 2011 | 1987 Chevrolet S-10 Pickup

1 Answer

How to replace the water pump on a 1992 geo tracker 1.6 liter engine


Water Pump - REMOVAL & INSTALLATION
During these procedures, identify all components removed from the engine so that they may be reinstalled in their original positions. If discarding the old components so that new components can be installed, identifying the old items is not necessary.


1.3L and 1.6L Engines

  1. Remove the timing belt cover, timing belt, tensioner, plate and spring.
  2. Remove the water pump mounting bolts.
  3. Remove the one (1.6L MFI engines) or two (1.3L and 1.6L TFI engines) small rubber seals from between the water pump and the oil pump, and the water pump and the cylinder head.
  4. If necessary for clearance, remove the oil level dipstick tube retaining bolt from the engine block and the alternator adjusting brace.
e6f342c.jpg

Fig. 1: Exploded view of the water pump mounting

WARNING Do NOT use a prybar between the water pump housing and the engine block to separate the two components; this can cause scratches and/or gouges, which can prevent proper sealing.
  1. Pull the water pump off of the engine block. If the water pump is difficult to remove from the engine block, use a soft-faced mallet to tap the water pump housing until it loosens.
Do not disassemble the water pump; if the water pump is damaged or defective, the entire unit is replaced.
  1. Thoroughly clean the water pump gasket mating surfaces of old gasket material and corrosion.
To install:
  1. Along with a new gasket, install the water pump on the engine block. Tighten the water pump mounting bolts to 88-115 inch lbs. (10-13 Nm).
  2. On 1.3L and TFI 1.6L engines, install two new rubber seals: one between the water pump and oil pump, and the other between the water pump and the cylinder head. The MFI 1.6L engines only use one rubber seal, located between the water and oil pumps.
  1. If removed, install the alternator adjusting brace and the oil level dipstick retaining bolt.
  2. Install the timing belt, tensioner, plate, spring and cover.

Hope helps (remember comment and rated this).

Jul 19, 2010 | 1991 Geo Storm

1 Answer

Water leak


I would suggest putting in a new water pump. You could take the existing one off and try to seal it but for me it would make more sense to replace it since you have the old one out. They're not too expensive. Mine was $20. You'll need a tube of high temperature gasket sealer to go around the edges of the new pump. Also, make sure you use the gasket that is with the new pump. Hope this helps ya.

May 24, 2009 | 1995 Subaru Impreza

1 Answer

Water pump removal


The water pump sits on the front of the engine and has your fan blade connected to it. Remove the fan and unbolt the water pump from the engine. When putting in the new pump make sure to compare to the old one and replace the old gasket with a new one as well.

May 05, 2009 | Mazda B3000 Cars & Trucks

1 Answer

91 trooper water pump replacement


If your car is over-heating, chances are it's the water pump or thermostat. These two parts should be changed out at the same time because if your pump is old enough to go out then the thermostat is not far behind.





Step1 serpentine247bs_thumb.jpg First you'll need to pull out the old water pump. Look in your vehicles owners manual and find the diagram showing what all that stuff under your hood is. locate the water pump (usually underneath alternator running on the same belt) you'll need to take this belt (serpentine or other) off to start pulling the old pump. There should be a tension bar or arm that easily loosens the belt with the right size socket. Step2 Once you've gotten the belt off you can begin to remove the old pump. There should be only a few large bolts holding it in. After you've gotten the old pump out, place the silicone sealer on the new water pumpmag-glass_10x10.gif 9around the edges where it meets the gasket. Then apply the sealer to the gasket as well, just use your fingers to spread it on. Now place the new pump with gasket, where the old one was, replace the bolts and be sure not to crank down too tight on the bolts or you might crack the gasket and your pump wont seal. Step3 thermo_thumb.jpg Now that you've gotten the new pump installed, you'll want to replace the thermostat. the thermostat could be located near the water pump or on the other side of the engine. So once again, refer to the vehicles owners manual and find where the thermostat is. You might need to remove some hoses and/or lines to get to the thermostat, so just be careful not to break/bend/crack or damage anything (the older the vehicle, the better chance of something breaking) Pull the old thermostat and replace it with the new and you're all done. Don't forget to put everything (hoses, lines, nuts'n bolts) back where they came from and off you go!





Mar 20, 2009 | 1991 Isuzu Trooper

1 Answer

How do you get to the water pump in a 1999 chevy cavalier


Make sure you don't have delco loc 2 or theftloc audio system before disconnecting the battery. You should be able to do this by contacting your local dealer and they run the vin and tell you.

Before you put in the new pump you need to put grease on the splines.

battery disconnected

drain coolant

take out the electric fan

take off the serpintine belt

use a large screwdrive or equivlent to hold the pump pulley and loosen all of the bolts holding the pulley on the pump.

After all are loosened then remove from the pulley and remove the pulley.

Take out the four bolts holding the pump to the engine block.

get a wood dowl or equilent and a hammer and give the old pump a few taps to break away the old seal.

Once the seals broke loose take the old pump out.

then clean up the block,

clean everything with brake parts cleaner

put RTV sealant on both sides of the new gasket and put it on the new pump.

try not to let the gasket move around so the bead isnt messed up to bad.

put the pump in and put all four bolts in finger tight

Torque on pump mounting bolts is 18 ft/lbs

Torque on pulley bolts is 18 ft/ lbs

then the rest is just reverse of removal

Jan 26, 2009 | 1999 Chevrolet Cavalier

1 Answer

Cannot remove the pulley from my 1991 olds cutlass ciera 's water pump. Its a 4cyl. Plus the new water pump doesn't look quite the same.


I replaced my water pump on my 92 olds, and the pulley will look slightly different because it's newer, but just make sure its the right one. The pulley does not come off of the water pump, both the water pump and pulley have to be changed. Your new one should come with both the pump and pulley already connected

Jan 05, 2009 | 1992 Oldsmobile Cutlass Ciera

2 Answers

Water pump


buy a new water pump, remove the radiator, remove the hose from the pump, remove the bolts that holds the pump, remove the old pump.

put the new gasket in the pump, dont forget to put a little bit of grease just to hold the gasket inplace. put the new pump, use the old bolts from where they are taken ( sometimes they are not of equal length ). if you have a torque wrench then use it to tighten the bolts with equal amounts of torque. put the hose back, put the radiator back, put water in the radiator, run the engine and look for some leaks at the new pump.

i hope i did it..

tnx, drcool

Jul 28, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Zanussi F1245W Front Load Washer Logo

Related Topics:

190 people viewed this question

Ask a Question

Usually answered in minutes!

Top Zanussi Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1464 Answers

shaun taylor

Level 3 Expert

1525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Are you a Zanussi Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...