Question about NetGear WG111 802.11g/b Wireless Adapter

1 Answer

I just bought NetGear WG111Wireless Adapter,I installed using The CD,but when is completed installing, the picture showed there are no connected with red cross sign on it, when I click to open network connections, it said there are no network range in my area, which I know it has , I'm not IT person, could plz someone guide me with a plain english how to solve the prob, or maybe i should also but the router as it said "maximum performance requires use with wireless routers(ah..so annoying) .thx

Posted by on

  • jlumenta Jun 22, 2009

    I changed to zero configuration, and it showed some of wireless network in range (oh...finally), thank to you :) ,but I just wonder with my other laptop it showed no red cross on the internet that i connected with wireless, but why with this old dell laptop (with I had prob b4) the screen keep said "no connected , plz right click for more options", but when I click left if showed some lists of networks connection in my area.I just want to know is it normal??with that words and red cross on it????as for your information, this laptop before used 1394 net adapter from wireless card D-link G630, since I made mistakes(do know how,....the setting gone, driver gone, and I do not have the CD anymore),the 1394 net addapter still in there it said connected and no redd cross sign on it, but it said disable.so confused.Or maybe because that 1394 net addaptor then the red cross sign showed up on my other network connection with this new wireless????any suggestion may be, sorry fo a long descriptions??

  • jlumenta Jun 22, 2009

    I double click but not changed.sometimes I can see some networks in range but some times it just blank.............weird, I think it because the signal, but the red cross signal keep shows, and I just realized that the scanning screen just change to red b4 green (it just keep telling me it scanning all the time)...I do not expert on this

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 220 Answers

When you search make sure it shows up "Searching for wireless networks in range" for a while.

If it doesnt and instantly says "no wireless found" is because you have another program using the wireless connections

To solve this simply click

  1. Start
  2. Control Panel
  3. Administrative Tools
  4. Services
  5. Scroll down to "Wireless configuration" or "Wireless zero configuration"
  6. Right-click and select "Start"
then you can search again

Hope it helps

Cheers

Posted on Jun 21, 2009

  • Claudio Barata
    Claudio Barata Jun 22, 2009

    It's normal alright, if you get "not connected" status just double click to reconnect.

    Cheers


  • Claudio Barata
    Claudio Barata Jun 22, 2009

    The cross will be present if you are not connected to that network I think



×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey. :) My name is Peyton. And me and my Dad have just bought a "NetGear N150 Wireless USB Adapter", And we've looked at the intructions, and we looked it up. But we can't seem to figure out how...


Installing the Software and Adapter

To install the wireless-N USB adapter with custom setup:

1. Insert the Resource CD. If the CD main page does not display, browse the files on the CD

and double-click Autorun.exe.
2. Click Install the Software.

Select one of the following methods to configure and manage your wireless network:

Smart Wizard. Allows you to manage your wireless networks with the NETGEAR

WNA1000 software and to connect securely using Push 'N' Connect.

Figure 1-1

Figure 1-2

NETGEAR Wireless-N 150 USB Adapter WNA1000 User Manual

1-5

v1.0, August 2009

- Configure network manually. Specify the settings for your wireless-N USB adapter

in the Settings screen.

- Configure automatically. Allow the Smart Wizard to automatically configure the

settings for your wireless-N USB adapter.

Windows Utility. Connect to and manage your wireless networks using only the

Windows configuration utility. For more information about Windows utilities, see the

Windows documentation or the NETGEAR application note at:
http://documentation.netgear.com/reference/enu/winzerocfg/index.htm.
See page 1-3 of the manual:
ftp://downloads.netgear.com/files/WNA1000_UM_05AUG2009.pdf

Click on this link or copy and paste the complete link into your browser.

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it and give a testimonial for my response. Happy Holidays!

Thanks, Joe




Dec 19, 2010 | Computers & Internet

1 Answer

Hi there, I just bought a new computer to which has the home network connection but my old computer now needs to be configured with my new NetGear WNA1100 WirelessN 150 USB Adapter to be able to have...


Since your computer can't read cd and you have the installation cd what you can do is to copy the contents of the cd to a flash drive from another system then use the flash on your own pc, and install it from the flash. Try this.

Thanks

Dec 14, 2010 | NetGear WNA1100 WirelessN 150 USB Adapter...

2 Answers

Not connected showed on my laptop


Hi,

Download the latest adapter driver for this adapter from the link below:

http://kb.netgear.com/app/products/family/a_id/1268

Install the adapter using thesr drivers and check if that helps.

Jun 21, 2009 | NetGear WG111 802.11g/b Wireless Adapter

1 Answer

Unable to Get Connectivity


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Enabling Wireless Zero Configuration Utility

1. Please click on Start, Run and type in services.msc and click on OK.
2. Scroll down and look for Wireless Zero Configuration. Right click on it and click on Start.
3. Right click on Wireless Zero Configuration again and click on Properties.
4. Under the General tab, set the Start up Type to Automatic and Service Status to Started. Then, click on Apply and OK.

Mar 24, 2009 | NetGear RangeMax NEXT WN511B...

2 Answers

Netgear wg111T Wireless Adapter 2.0 connectivity issues


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Jan 02, 2009 | NetGear WG111U 108 Mbps Wireless USB 2.0...

3 Answers

Cant connect wirelessly


Yes u have to buy a netgear N dongle ...
Because N works on 5 ghz and G works on 2.4 Ghz
You can buy netgear WN111v3

Nov 19, 2008 | NetGear : WG111 54 Mbps Wireless USB 2.0...

1 Answer

Cannot connect to my laptop with a built in wireless.


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Jul 13, 2008 | NetGear WG111T 108 Mbps 802.11g Wireless...

2 Answers

Hi there, I just bought a netgear Rangemax next wireless router WNR834B with RANGEMAX™ NEXT WIRELESS N USB 2.0 ADAPTER – WN121T with no installation CD and i have connected the router to my modem and its...


Get the driver for the WN121T from the NetGear webset and install it before pluging the adapter into the notebook. Use a wired connection on the notebook until you have the drive downloaded.

Jun 19, 2008 | Computers & Internet

1 Answer

Wireeless


Wireless Adapter Installation

A. Install the software.

Note: Firewall and anti-spyware need to be disabled. They sometimes treat software installation as a behavior of a spyware and therefore will prevent installation.

Windows XP:

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter Resource CD into your CD-ROM drive. The CD main page shown at the right will then load.
3. Click the Install Driver & Utility.
4. Please make sure that you follow the Install Shield Wizard steps. Click Finish when done and turn off your computer.

Windows 2000/ME/Win98SE:

Note: Windows 2000 may require you to be logged on with administrator rights.

1. Please power on your computer. Allow the operating system to boot up completely and log in as needed.
2. Insert the NETGEAR adapter resource CD into your CD-ROM drive. The setup page will then load.
3. Afterwards, click on the Install Driver & Utility link.
4. Make sure to follow the Install Shield Wizard steps, and click Finish when done to restart your computer.

B. Install the adapter.

Windows XP:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Please insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. When the Found New Hardware Wizard displays, please click on Next and then follow the prompt. If you are prompted with a Windows XP Logo testing message, just click on Continue Anyway.
5. After the installation completes, click Finish to close the wizard.

Windows 2000/ME/Win98SE:

1. Please make sure that you shut down the PC first and then remove the power cord.
2. Insert the NETGEAR adapter into the available expansion slot.

Note: If you have PCI adapter, connect the antenna to the adapter, making sure the antenna is in the upright position.

3. Reconnect the power cord and reboot the computer.
4. On the Found New Hardware Wizard, click on Next, then follow the prompt to proceed.
5. After the installation completes, click Finish to close the wizard. Please make sure that you can see the NETGEAR icon located at the lower right portion of your computer screen.

Note: If Windows displays Digital Signature Not Found warning, click Yes to continue.

C. Configure the NETGEAR adapter.

1. Please Double click on the NETGEAR icon on the right lower end portion of your computer.

Note: If you do not see the icon, click on Start and go to Programs. Locate the NETGEAR Utility and click on the NETGEAR Smart Configuration Utility.

2. Click on the Networks tab.
3. Click on the Scan button.
4. Select the Network Name or SSID of your wireless network.
5. Click on the Connect button.
6. You will be directed to the Settings tab.
7. Type a name for the Profile.
8. The Network Name (SSID) will be the same with your wireless network.
9. Make sure that the Network Type is set to Access Point (Infrastructure).
10. Select the Security that you are using on your wireless router.
11. Click on Save Profile.
12. Click on the Apply button.

Feb 12, 2008 | NetGear Wireless

Not finding what you are looking for?
NetGear WG111 802.11g/b Wireless Adapter Logo

Related Topics:

265 people viewed this question

Ask a Question

Usually answered in minutes!

Top NetGear Computers & Internet Experts

Prashant M
Prashant M

Level 3 Expert

2260 Answers

Doctor PC
Doctor PC

Level 3 Expert

7733 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18409 Answers

Are you a NetGear Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...