Question about Razor MX500 Dirt Rocket

3 Answers

Rode mx 500 in light rain, stopped working. Batteries ok and LED

When throttle is turned you can hear a clicking sound from battery compartment. What can I do to fix? Thanks

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Plz.we have to use a little common scense in this case.The razor-dirt rocket 500/or any model that run on _Electricity can not get "wet" for any reason.For example what happens when you drive a remote control car in water? The electrical motor dies,not before smoking first. It is nyeve of the manufacture to not a protective cover on or around the motor, which electricity flows inside. the 3 vent holes is for heat ventilation

Posted on Dec 30, 2012

  • Jim McDonald
    Jim McDonald Feb 01, 2014

    this is not the right answer. Best guess is the battery or the controller. Call Razor's support hotline.

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I had the same problem i put a heater on the motor and it must have dried something and it worked
The motor must be getting wet i had power to the motor but the motor would not come on to i put the heater on oit

Posted on Jan 31, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

MAKE SURE BATTERY IS OK. REMOVE BATT
CONNECTIONS AND THOROUGHLY CLEAN
BATT POSTS AND CONNECTIONS WHERE
THEY FIT ON POSTS, RECONNECT AND TRY.
IF STILL NO CRANKING, MAYBE BATT IS GONE.

Posted on Jun 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When my E2d. Ed defender. 200 lumens flash light is turn on it act like an strob light how to stop it or is it a weak batteries


No, that is a 'feature'. It is for signalling or blinding an attacker.

This is the instructions for the 500 lumen version but it will be the same. Nice light, I run Fenix Tactical. Strobe is usually gained by switching on and then half depressing the button and holding. If this doesn't work, contact Surefire direct.

The E2D LED Defender® Ultra is a compact 500-lumen flashlight featuring dual-output capability and self-defense enhancements. Utilizing a virtually indestructible high-performance LED and a Total Internal Reflection (TIR) lens, the E2DL Ultra is activated with a pushbutton tailcap click switch that also selects output levels: press or click once for a high-intensity 500-lumen white-light beam-ten times the light needed to overwhelm the night-adapted vision of an aggressor. Return to off and press or click again within two seconds for a 5-lumen ultra-long runtime low beam that's suitable for navigating at night or performing close-up tasks for hours. The Defender's crenellated Strike Bezel® provides further defensive options should the need arise. Slender and powerful, the E2DL Ultra is an ideal everyday-carry light.

Jan 08, 2016 | Surefire E2D LED Defender Flashlight Max-...

2 Answers

Sccoter's batteries are two years old, fully charged but when the scooter goes forward or backward, it makes a clicking noise and just stops for no reason.


Charge the scooter and test the volts cheap volt meter. When you hear the clicking retest. If the voltage is way down the battery is bad. If voltage is ok then and electrical component like a relay needs to be replaced. Any small electronic shop can repair it. Also, Google the model and clicking behavior to see if a turn key fix exists.

May 05, 2015 | RTO Mega Motion 3 Wheel Travel Pal Scooter

1 Answer

No charge indication on throttle and motor doesn't work - New charged batteries.


Make certain the Batteries are IDENTICAL to the original. Any change of the Voltage, Current, or Amps will damage the motor or starter. Check all connections to see if they are properly set and Plus is to Plus and Minus to Minus. Check the Ground wires. Make certain all wires are insulated well, no cuts, peeling, cracks, or holes. Technically speaking, if you do not have test equipment like a VOM (Meter) you cannot check continuity (for shorts) and leaks.
If you are satisfied that we are tryting to help you, rate the person accordingly.

Apr 02, 2014 | Electric Currie EZIP 500 Scooter

1 Answer

Batteries are charged and the bike doesnt work any ideas on what it might be and batteries are new


yes! if that's the case ,the motor is the culprit.there are 4 things that make our bike run..the a good charger, batteries, the throttle, and the motor. now that you singled out your battery and charger ,you have the throttle and your motor..1st check your throttle & make sure it stops @ a1/4 twist.check all connections, then do an extencive check of your motor for moisture or water/signs of it being wet/riding in the rain..which is a big No-No../no rain No snow, No drizzle,and no puddles clean or muddy..it is not a gas bike....remember!great tip!

Dec 20, 2012 | Razor MX500 Dirt Rocket

1 Answer

I bought a World Tech Toys ZX-A68690 helicopter and I cant get it to work. I charged the battery pack as outlined in the operation manual. I installed the "AA" Duracel batteries in the...


Try turning the controller power on ( before turning on the chopper) and then quickly moving the left throttle stick up to the fastest setting and then immediately back to the slowest speed setting...The flashing should stop. This calibrates the remote throttle range.
Turn on the helicopter and you should be OK

Jun 01, 2011 | Worldtech Devices Toys

1 Answer

Pentax mx won't stay on. As soon as I turn it on the camera turns its self off. Before it does that you hear a clicking sound.


If the camera has recently been dropped you may have lens damage that is preventing it from powering up. If it hasn't been dropped your problem may be due to weak/worn out batteries or corrosion on the battery contacts inside the camera which can prevent the full power of the batteries from flowing into the camera. Try this free fix before you do anything else: remove the batteries and wipe the camera contacts firmly with a dry cloth (heavy corrosion may require cleaning with a wire brush, steel wool, or sandpaper). Remove any residue that may have fallen into the battery compartment during cleaning, then wipe both ends of the batteries and place them back in the camera and give them a full charge (assuming that you are using rechargeable batteries). This cleaning clears the problem about 90% of the time. If it doesn't work for you, your batteries may need to be replaced or the camera may have a problem that requires professional repair.

Dec 15, 2009 | Pentax Optio MX4 Digital Camera

2 Answers

Wii remote is not turning on


You probably need to re-sync the Wii Remote.

Standard Mode SynchronizationNote: Make sure you have placed batteries in the Wii Remote.
  1. Press the Power button on the Wii console to turn it on.

  2. Open the SD Card Slot cover on the front of the Wii console. Remove the battery cover on the back of the Wii Remote you wish to sync up.

  3. Press and release the SYNC button on the inside of the SD Card compartment on the console. Press and release the SYNC button just below the batteries on the Wii Remote.

  4. When the Player LED blinking stops, the syncing is complete. The LED that is illuminated indicates the player number (1 through 4).
  5. wiiremotesynchstandard.gifThis procedure must be followed for each additional Wii Remote added to your system.

Source: http://www.nintendo.com/consumer/systems/wii/en_na/setupWiiRemote.jsp#Synch

Oct 20, 2009 | Nintendo Wii Console

2 Answers

It dosent go when on


maybe the battery is dead

Aug 21, 2009 | Razor MX500 Dirt Rocket

3 Answers

Indicator light fully charged...but barely enough power to move


i have the same exact problem on 1 of my sons MX5s..i checked all 3 batteries and all that! you left out the controller clicks when the back wheels sapose to be moving ,it's not....so worse case scenerio batt,controller,motor,(650 This time)& throttle....So theres our blue print...lets hope it's just the batteries....!

Mar 30, 2009 | Razor MX350 DIRT ROCKET - BLUE

Not finding what you are looking for?
Razor MX500 Dirt Rocket Logo

1,014 people viewed this question

Ask a Question

Usually answered in minutes!

Top Razor Cycling Experts

Ted Maxwell

Level 3 Expert

3519 Answers

ray gallant

Level 3 Expert

44435 Answers

 steve
steve

Level 3 Expert

5482 Answers

Are you a Razor Cycling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...