Question about Mk Diamond Wet Saw with Stand

1 Answer

MK101 won't start

Installed new water pump, saw is set up and it is all plugged in, when I flip the switch to start it, all I get is a big buzz sound. Nothing moves on the saw. I have unplugged, replugged, verified water pump is connected correctly. I have it plugged into regular outlet (110 v). The outlet is functional. The saw plug is a different kind of plug, not sure. Can anyone help? Thank you.

Posted by on

  • Chris Longsien May 11, 2010

    Does the blade turn freely? If not then it sounds like the shaft bearing is frozen.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 55 Answers

Can you move the blade with your hand or does the blade not move at all or is the sound buzzing even with the blade spinning cuz mostly this sounds like the blade is stuck and should be able to free it by moving it by hand unplugged all the debris from the tile dust can lock up the blades sometimes if it is not cleaned properly

Posted on Dec 02, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 Taurus 3.8 SHO wont start replaced everything fuel pump to big relay is buzzing even new one im lost need help


Run tests. Fuel pressure correct? Spark at plugs when cranking? Fuel injector pulse working? Compression test?

Apr 06, 2015 | Cars & Trucks

1 Answer

91 Chevy Tracker won't start. went the ought big


Sounds like you have water in some of your distributuin boxes. Remove the covers and blow them out with compressed air.

Jun 17, 2013 | Cars & Trucks

1 Answer

Frigidaire front load washer that will not start . it just buzzes. when it does start it stops after washing and leaves water in clothes asn buzzes.


it could either be a bad door switch or something stuck in the pump or a bad pump.if you set it to drain/spin will it drain out the water or does it buzz there?if it does drain i'd have to say you have a bad door switch.the model number you sent doesn't come up,you can unplug the machine,remove the hose that goes to the pump or run it before you unplug it and see if it's the pump making the sound or if the center of the pump can be removed to clean out the pump and check the pump for coins and junk,use a shop vac and vac out all the water in the tub and then lossen the hose or center of pump until water starts to leak out and vac it up as it comes out,check the pump and put it back together,add some water with a bucket or something and see if it drains out,if it doesn't drain and it sounds like the pump is making the noise you have a bad pump,if it buzzes and it's not the pump change out the door switch.the buzzing is electrical,things that could make this sound are the motor,the solenoids on the water valve or the door switch,if you can do some checks like see if it drains or try to find where the noise is coming from would be helpful.good luck and i hope this helps you out.

Oct 29, 2011 | Frigidaire ATF6000ES Front Load Washer

1 Answer

On/off switch just buzzes when I push start. I can't find a reset button on the JET XACTA SAW DELUXE 3HP,1PH, 50" RIP table saw. It's getting electricity- plugged in and continuity of...


I am thinking that you have a problem with the capacitator (if it has one) or the starter windings/switch in the motor itself. If the switch buzzes you are getting electricity to the motor but it isn't rotating and that is where I would start to look. Before this happened did the saw make any unusual sounds or have any problems??? Also unplug tool and look for any obstructions that might have stopped the blade.

Jul 02, 2011 | Exacta DELUXE XACTA SAW 3HP, 1Ph, 50? Rip

1 Answer

When I turn the key in the ignition I don't hear anything and my car won't start. I tested the started and it is fine. I replaced the ignition switch. Could it be my alternator or my neutral safety switch...


no. the noise you're not hearing is the fuel pump. When u turn ur key on you should hear a buzzing like sound from the rear of the vehicle. If not, and ur car don' start, probably fuel pump. Just to verify the faulty fuel pump, have an assistant open the fuel tank cover and remove the gas cap itself. With you inside turn just the key on, and have your assistant listen for the "buzzing" or "hummin" sound. if nothing there, then faulty fuel pump. If noise is present, then perhaps you have a different problem like nothing is reaching the engine, fuel wise. Like a plugged fuel filter. when replacing the fuel pump, ALWAYS do the new strainer as installing the old one could cause a whole new set of problems and eventually wipe out the new one as well *RULE OF THUMB, WITH NEW FUEL PUMP, REPLACE FUEL FITLER.* this will be easier on the pump output to the engine. good luck.!

Aug 24, 2010 | 1994 Jeep Grand Cherokee

2 Answers

Kenmore front loading washer won't drain or aggitate, just buzzes


take the front bottom panel off. inside there is a drain pump. you need to remove filter from drain pump its look like a knob. be careful because their is water inside your drain pump so use some big thing for water. clean your filter. put filter back tight. i hope will solve your problem.

May 23, 2009 | Kenmore 43142 Front Load Washer

1 Answer

Dewalt ds2400 wet saw will through in line breaker not start


sounds like the breakers working to good,i would by pass the reset switch,most likely that switch is bad anyways,we always plug our saws into a outlet box that has a breaker in it ,you know those reset switches are stupid, by pass the reset switch like it wasnt even there,and if that works i would replace the whole cord with a new 1,and buy a 5 dollar junction box that has a breaker in it,i dont know if there is a seperate plug on that saw where u plug the water pump into, if there is i would check that plug first before you bypass the switch.good luck chad

May 14, 2009 | Dewalt D24000S Wet Saw With Stand

1 Answer

No voltage at water pump plug on MK 101 off switchbox.


The Capacitor is only for starting the main motor and not the water pump. Like you said, if you connect the water pump to 110V it will run so there is a problem with how it is wired to the on/off switch. there should be a white wire (neutral) permanently connected to the pump and the on/off switch should supply power on the black wire when turned on.

Apr 05, 2009 | Diamond Products Mk - 101 10" Tile Saw

2 Answers

Baby gaggia wont pump


The pump may only have lost its prime. To prime the pump:

Fill an ear syringe (available at most pharmacies) with water. Insert the business end of the syringe securely in the tube that normally takes up water from the reservoir. As you squeeze the syringe bulb, flip the brew switch on. If you see movement of water in the tube, and hear a change in the sound the pump is making, flip the brew switch off, remove the syringe, and put the tube back in the filled reservoir. Now flip the brew switch on, and see if the pump can draw water on its own. Repeat several times if necessary. If the pump still won't pull water, then it must be replaced.

www.espressosolamente.com

Apr 21, 2008 | Gaggia Baby Espresso Machine

Not finding what you are looking for?
Mk Diamond Wet Saw with Stand Logo

Related Topics:

276 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mk Diamond Saws Experts

Tom Chichester

Level 3 Expert

34767 Answers

ray gallant

Level 3 Expert

44341 Answers

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

1805 Answers

Are you a Mk Diamond Saw Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...