Question about Computers & Internet

2 Answers

Plotter mt871 will not communicate from computer to plotter

Brought a plotter joys mt871 these are inported from china my make is a kerring 630??? does not come with instalation disc only usb lead this is surpose to be a plug and play but when i plug in the usb it picks up the usb plugged in but will not come up (found new hardware so unable to install)

Posted by on

  • courierforu2 Jun 22, 2009

    thanks for the advice will try both options to see if i can get going

  • rwc120 May 11, 2010

    Make sure you check your device manager hardware devices. If it's not in there anywhere I would venture to say you need some sort of installation disc. Plug and play is used incorrectly sometimes by these companies that want to make a sale. Good luck.



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Reset the plotter and enter the setup menu. Calibrate your baud rate which should normally be 4800.

Posted on Aug 24, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 115 Answers

Try getting some generic drivers for plotters and see if they do anything... I would also suggest that you get a JetDirect card or something to interface the Plotter with your network, this should take any misscommunication away.

Posted on Jun 22, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

HP 1055cm+ Plotter: System Error 060308 00000008. How do you access the printheads when the plotter has this error? None of the console buttons respond.

This is an APA regulation failure. Not a good error. First you need to remove all the printheads and clean the contacts on the printheads and the contacts on the flex connector inside the carriage assembly that mate with the contacts on printheads. If no joy you need to perform the electronics test contained in the service manual link below. If still no joy then you need to replace all the printheads.

Aug 22, 2017 | HP Office Equipment & Supplies

1 Answer

I bought a used HP Design Jet 450 C...But its showing the cartridge and data solid orange light and ready light is constantly green. I brought a new black cartridge, the printer takes in the paper and...

I think the problem is not the computer. You shoud check the plotter by running the test print without the computer. When plotter's power is on, press Setup and Cancel keys simultaneously. If it does not print, then the plotter need repair.
According to your descriptions, there is System Error Code shown on your control panel. when the lights on for Ready+Cartridges+Data (DKL), it may have 9 possible causes referred by Service Manual page 2-7. You can check all these 9 items to see which one causes the problem.

Dec 17, 2010 | HP DesignJet 450c InkJet Printer

1 Answer

Weak or no coffee

Hi, Go to eBay, search for Farberware coffee pot parts. You will see my auctions for parts, I have all the parts you might need. Your pot is a china 4 cup. Meny people are having bad luck with the inports from China. I should be able to help. Ron

Aug 01, 2010 | Coffee Makers & Espresso Machines

2 Answers

Need s registration key for xitel inport to put on my computer

I bought my'n from the home shopping channerl for $89.00
works excellent.

Feb 06, 2010 | Xitel INport (HFLI1X1) Audio Input

2 Answers

I lost ALL sound when Iinstalled Xitel's Inport

Have you trying to rollback using windows sistem restore

Aug 23, 2009 | Xitel INport Deluxe for PC

1 Answer

Can install the software

just insert the cd provided with the player when it asks to install the driver and let it search and install the driver automatically...

Apr 01, 2009 | Transcend T SONIC 630 MP3 Player

1 Answer

How do i print the usage page

You should be able to communicate with the plotter and get a control screen, through your browser, by typing in it's ip address. (i.e.

Also, from the plotter, under utilites, you can view/print a usage report.

Nov 23, 2008 | Office Equipment & Supplies

Not finding what you are looking for?
Computers & Internet Logo

Related Topics:

831 people viewed this question

Ask a Question

Usually answered in minutes!

Top Computers & Internet Experts

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Alun Cox

Level 3 Expert

2678 Answers

David Payne
David Payne

Level 3 Expert

14162 Answers

Are you a Computer and Internet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides