Question about Keurig B60 Coffee Maker

1 Answer

Not ready light stays on. will not go to ready

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Open k-cup holder and close,wait a few seconds and brew light will come back on.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When ready to seal red light stays on


Seal 200 lights - Photo.net B&W Photo - Printing & Finishing Forum

photo.net > ... > Prints & Print Presentation

Jul 29, 2004 - 4 posts - ‎3 authors
I'm sure one is a ready light but would really like to know the details. ... I have the Seal110S unit and the red (really orange) light stays on when ...

SmartSeal™ V3800 Series at FoodSaver.com.

www.foodsaver.com/...sealers/smartseal.../vacuum-sealers-help-and-...

TiliaHow does the new FoodSaver® with SmartSeal™ Technology sense the ... My unit isstuck, it will not open, and unit is not allowing me to feed bag into unit to ...

Quickstart Guide for Hospital Staff - Creche Innovations

crecheinnovations.com/new/wp-content/.../Quickstart_Guide_2012.pdf
Seal the blue zipper tightly. Place feeding into inner bag. Seal the ... Ready. When red light is on. • Warming is occurring. When green light is ... light stays on.

What Causes the Brake Warning Light to Come On ...


Jan 05, 2016 | Cars & Trucks

1 Answer

HP2550 problem:The attention light, the ready light and the go light stay on (not flashing). When I hold the Go and Cancel button down, the attention light and the ready light stay on (secondary light...


According to your "secondary" light pattern your printer has a Carousel motor error.
You've already power cycled it to no avail.
The next step is to get the motor replaced.

Sorry, I know that you didn't want to hear that.

Apr 06, 2011 | HP LaserJet 2550L Printer

1 Answer

Airbag light says on: when tested it was ready to depoy why


When your airbag light is on, it means that the air bag system is malfunctioning, and not ready to deploy. You will need to take it to a dealership where they actually have the knowledge to find and fix your problem.

Jul 02, 2009 | 1999 Buick Century

2 Answers

Eiki LC-XG110 lamp going off


Lamp is near end of life. Try reseting lamp timer and order new lamp if unit stays on

May 13, 2009 | Eiki LC-XG110 Multimedia Projector

1 Answer

Sb600 display fine, but no longer flashes


Your flash has a bad flash tube . make sure the batteries are in corectly and youhave a ready red light .

Nov 08, 2008 | Nikon Speedlight SB-600 TTL Flash

1 Answer

Ready lamp on 283


When the flash goes into battery saver mode, which it does automatically, the light will blink.
If you are using the external power source, the light should remain steady.
Jeff

Oct 30, 2008 | Vivitar 283 Flash

1 Answer

Brother Laser Printer HL 1440


tray this
The procedure for the factory inspection mode is as follows.
(1) Turn off the printer power switch, open the front cover, and remove the drum unit.
(2) Turn on the printer power switch while holding down the control panel button. The Drum
LED comes ON.
(3) Lightly press the panel button again.
(4) Check that all the LEDs except the Ready LED are OFF.
✒ If the toner sensor is ON, the Drum LED stays ON (error).
✒ If the front registration sensor is ON, the Alarm LED stays ON (error).
✒ If the upper paper cassette sensor is ON, the Data LED stays ON. (error) (HL-1250
only)
NOTE:
The lower paper cassette solenoid is turned ON/OFF even if the panel button is not pressed.
(5) Check the rear registration sensor.
✒ If the rear registration sensor is stuck backwards, the Ready LED stays OFF. (error)
✒ If the rear registration sensor is moved back and forth, the Ready LED comes ON at
any time. (error)
(6) Check that only the Data LED comes ON while pressing the panel button.
✒ If the paper eject sensor is ON, the Drum LED stays ON. (error)
✒ If the lower paper cassette registration sensor is ON, the Ready LED stays ON. (error)
If the registration sensor is ON, the lower paper cassette solenoid is turned ON, and
the Ready LED also stays ON. (HL-1250 only)
NOTE:
The lower paper cassette solenoid is turned ON/OFF even if the panel button is not pressed.
(7) Install the drum unit.
✒ Check that the Drum LED goes ON and the Ready LED goes OFF.
(8) Close the front cover.
(9) Continue to press the control panel button.
✒ Check that the Data LED stays OFF.
(10) Release the panel button.
(11) If all the sensors except the toner sensor are correct, the printer goes back to the Ready
status.
If any error is detected, the printer stays in the inspection mode.

Apr 01, 2008 | Brother HL 1440 Laser Printer

Not finding what you are looking for?
Keurig B60 Coffee Maker Logo

694 people viewed this question

Ask a Question

Usually answered in minutes!

Top Keurig Coffee Makers & Espresso Machines Experts

Lisa
Lisa

Level 2 Expert

91 Answers

Jason

Level 2 Expert

211 Answers

Cindy Wells

Level 3 Expert

5123 Answers

Are you a Keurig Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...