Question about Swintec 4600 DP Electronic Calculator

Open Question

How to open Swintec 4600 DP to change ribbon - Swintec 4600 DP Electronic Calculator

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3594 Answers

SOURCE: swintec 7040 typewriter ribbon feed.

Try code . or , or / one of these should reset the ribbon feed to full spacing

DickyO

Posted on Mar 10, 2008

  • 3594 Answers

SOURCE: Swintec 8016 / the ribbons jam up

When you load a ribbon there is a black rubber feed roll on the L. side that feeds the ribbon they be come loose on the plastic spindle. It should be replaced but a little pliabond or similal cement mat reattach it. (JUST A LITTLE)

Posted on May 13, 2009

  • 3594 Answers

SOURCE: change a swintec 1186 typewriter ribbon

Move the red lever to the front of the ribbon, remove it, drop the ribbon in place, be sure it goes thru the feed roller on the left, move the lever back, done.

DickyO

Posted on Oct 28, 2009

  • 3594 Answers

SOURCE: swintec 2600. Ribbon is not advancing properly. Types in same place randomly.

You may be in the overstrike ribbon mode. Try code and . , or / one will get you out of the mode.

DickyO

Posted on Jul 08, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the ribbon on Swintec 1146?


Swing the lever located below the ribbon carrier to the right to release the ribbon then lift up

Mar 03, 2015 | Swintec Office Equipment & Supplies

1 Answer

What correctable carbon ribbon does the swintec 7040 take


The re-order number on the ribbon you need is SWS1009, 7000 series ribbon from Swintec.

May 25, 2011 | Swintec 7040 Typewriter

1 Answer

For a Swintec 8014 typewriter: the bottom portion of the letters are not tranferring to the paper when the keys are striked. although the ribbon shows the full letter being striked, only the top portion...


Check to be sure the ribbon dosen't have a fold in it and is fully seated in place, be sure the platen is fully seated in the side frames, check the correction tape for proper imstallation it can rob the print if to high.

DickyO

Dec 03, 2010 | Swintec Office Equipment & Supplies

1 Answer

How do I install the ribbon in the swintec 8014-S PLEASE HELP


Move the red lever to the front, lift out old ribbon, put in new ribbon putting it thru the 2 lifter arms, move the lever back.

DickyO

Sep 03, 2010 | Swintec Office Equipment & Supplies

1 Answer

Change a swintec 1186 typewriter ribbon


Move the red lever to the front of the ribbon, remove it, drop the ribbon in place, be sure it goes thru the feed roller on the left, move the lever back, done.

DickyO

Oct 26, 2009 | Swintec Office Equipment & Supplies

1 Answer

Swintec 7000 Typing Problem


Try Code comma, peroid or slash one of them will get you out of the overstrike ribbon mode.

DickyO

Jul 08, 2009 | Swintec 7040 Typewriter

1 Answer

Swintec 8016 / the ribbons jam up


When you load a ribbon there is a black rubber feed roll on the L. side that feeds the ribbon they be come loose on the plastic spindle. It should be replaced but a little pliabond or similal cement mat reattach it. (JUST A LITTLE)

May 13, 2009 | Swintec Office Equipment & Supplies

1 Answer

Typewriter - Swintech 2640


Sounds like you need a new ribbon or you are using non-Swintec compatible ribbons that are not properly aligned to your ribbon feed. Try using Swintec brand ribbons and see if this still occurs. Worst case scenario, you need to have your ribbon feed adjusted at your local dealer.

Jay @ www.granadahillsbusinessmachines.com

Aug 08, 2008 | Swintec 7040 Typewriter

1 Answer

Ribbon retainer clip installation??


Possibly came from the ribbon cartridge. Try another ribbon.

Mar 27, 2008 | Swintec 7040 Typewriter

2 Answers

Swintec 7040 typewriter ribbon feed.


The typewriter is supposed to automatically adjust itself to the type of ribbon you have installed. Have you tried a different ribbon?

Feb 11, 2008 | Swintec 7040 Typewriter

Not finding what you are looking for?
Swintec 4600 DP Electronic Calculator Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Swintec Office Equipment & Supplies Experts

James Cagle
James Cagle

Level 2 Expert

453 Answers

Jim Keysor

Level 2 Expert

329 Answers

Anthony Karuku

Level 2 Expert

255 Answers

Are you a Swintec Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...