Question about LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher

Open Question

The brackets will not hold the washer in place

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wd62p replace hinges


Hi there,

First of all remove the door from the machine by unscrewing the screws on the hinge than remove clip at the top of door seal, when it unclips remove metal band, pull front of door seal off of front panel, Pick up metal bracket. Now with the hinge attached to door hold in place and place bracket behind the two holes fit screws and then fit the seal and clip.


Regards

May 05, 2012 | Hotpoint Ultima WD72 Front Load...

1 Answer

Hotpoint Washer


if you have rust underneath washer its time to replace same.

Nov 28, 2011 | Hotpoint Washing Machines

1 Answer

How to change the alternator on my 2000 grand voagear


This is for a 3.3L motor
Hope this helps, it it does please leave feedback and vote Thank You and Good Luck

REMOVAL

  1. Release hood latch and open hood.
Removal/Installation of Battery Cables 81929864

  1. Disconnect battery negative cable.
  2. Remove windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  3. Remove accessory drive belt.
Generator Mounting Bracket 81929870

  1. Remove bolt holding top of generator mount bracket to engine air intake plenum.
  2. Remove bolts holding outside of generator mount bracket to generator mount plate.
  3. Remove bolt holding top of generator to mount bracket.
  4. Remove generator mount bracket from vehicle.
  5. Rotate generator toward rear dash panel.
Generator 81929868

  1. Disconnect the push-in field wire connector . from back of generator.
  2. Remove nut holding B+ wire terminal to back of generator.
  3. Separate B+ terminal from generator.
Generator Pivot Bolt 81929871

  1. Remove bolt holding bottom of generator to lower pivot bracket.
Generator 81929872

  1. Remove generator from vehicle
INSTALLATION

  1. Place generator in position on vehicle.
  2. Install bolt to hold bottom of generator to lower pivot bracket.
  3. Place B+ terminal in position on generator.
  4. Install nut to hold B+ wire terminal to back of generator.
  5. Connect the push-in field wire connector into back of generator.
  6. Rotate generator forward away from dash panel.
  7. Place generator mount bracket in position on vehicle.
  8. Install bolt to hold top of generator to mount bracket.
  9. Install bolts to hold outside of generator mount bracket to generator mount plate.
  10. Install bolt to hold top of generator mount bracket to engine air intake plenum.
  11. Install accessory drive belt.
  12. Install windshield wiper housing, refer to the Windshield Wipers and Washers for proper procedures.
  13. Connect battery negative cable.
  14. Verify generator charge rate.

Jan 02, 2011 | 2000 Plymouth Grand Voyager

2 Answers

Where is the location of the battery in a 94' cutlass supreme ls?


Pictures coming next!

CAUTION Always make sure that the ignition is OFF when disconnecting or connecting the battery cables. Failure to do so may cause damage to the computer control module or other electronic components.

  1. Make sure the ignition is OFF . Remove the air cleaner assembly if necessary, and disconnect the negative battery cable, then the positive cable.
  2. Unfasten the retaining bolts, then remove the cross brace.
  3. If equipped with Anti-Lock Brakes (ABS), remove the relay center and bracket, then position aside.
  4. If necessary, detach the electrical connector and hose from the windshield washer pump, then unfasten the reservoir retaining nut and remove the reservoir.
  5. Remove the air cleaner bracket upper attachment bolt.
  6. Unfasten the battery heat shield, hold-down bolt, and retainer.
  7. Remove the battery from the battery tray.
To install:
  1. Place the heat shield on the battery, then position the battery in the vehicle.
  2. Install the retainer, air cleaner bracket and hold-down bolt. Tighten the hold-down bolt to 13 ft. lbs. (18 Nm).
  3. Install the air cleaner bracket upper attachment bolt. Tighten the bolt to 35 inch lbs. (4 Nm).
  4. Position the windshield washer reservoir and secure with the retainers. Attach the hose and electrical connector to the windshield washer pump.
  5. If equipped with ABS, install the relay center bracket and relay center.
  6. Position the cross brace, then secure with the retaining bolts. Tighten the front bolt to 18 ft. lbs. (25 Nm) and the rear bolt to 35 ft. lbs. (47 Nm).
  7. Connect the positive battery cable, then the negative battery cable. Tighten the cable bolts to 11 ft. lbs. (15 Nm).
  8. If removed, install the air cleaner assembly.

Oct 20, 2009 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Lid switch replacement


unplug washer first. dont know your washer make but some of the older units the top comes off by removing screws from a bracket just below the control panel on the back of washer. lift top which will allow you to remove screws that hold switch into place. wires should unplug.

Aug 22, 2009 | Kenmore Washing Machines

1 Answer

Cannot remove CCU


1. UNPLUG the washer.
2. Remove the washer top panel by removing the three screws that hold the panel in place in the rear of the washer. With the screws removed, the panel will slide back, then off.
3. The CCU is located directly behind the wash tub.
4. With the new CCU in hand, carefully disconnect each connector from the old CCU and swap them one at a time with the new CCU. (This is the easiest method I know of to do this. This will avoid the possibility of getting any connectors crossed).
5. Once you have all the connectors moved to the new CCU, use a screwdriver to lift up on the release tabs that hold the old CCU to the mounting bracket and remove.
6. Now carefully insert the new CCU with all the connectors in place on the mounting bracket and snap into place.

Another method is to use a digital camera to take photos, or use the tech sheet that is located inside the washer (behind the lower panel under the door). The tech sheet should have an illustration showing all the connector locations.
<courtesy guru jsrock517>

Mar 26, 2009 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

REPLACING BELT


Hello, This is somewhat involved and time consuming, but if you are handy, it can be done. First unplug the dryer then start with the two screws in the hinges of the door and then the door lifts out. Two screws on the opposite side holding plastic spacers. Once these four screws are out the front panel tilts right out. The front panel will come off then 4 more holding on the front tumbler support and air duct. Removed wires from light and dryness sensor and clips holding wires to panels. Pull out the tumbler and removed belt. If your dryer gets a lot of use, then you might want to keep going and replace some more wear items while you have it apart. Remove the two drum support rollers and shafts by removing a nut on the back side of each shaft. Remove snap ring off each old shaft, install new rollers and fiber washers onto new shafts, reinstall snap ring and replaced on brackets with the old nut. Remove tension spring off idler pulley bracket and one screw holding on the bracket. Install new pulley and fiber washers on new bracket and reinstall bracket and spring. Placed new belt on tumbler and reinstalled tumbler. Used drill and bit to drill out pop rivits holding on the two front glides that are attached on the front tumbler support and installed new glides and pop riveted in. Reinstall front support and air duct checking that felt tumbler seal front and rear are in place. Placed new belt on motor pulley and idler pulley. Reinstall front panel.

Dec 01, 2008 | Maytag Neptune MDE5500AY Electric Dryer

1 Answer

Getting lid off kenmore oasis canyon capacity washer


Okay, here ya go! There are 2) screws attaching 2) brackets to the back of the machine. This holds the lid in place. When attempting to do this bring a friend or family member to help hold the lid. You then slide the front top back slightly. this will allow access to the drum. Now there are several little slots holding the drum top into place, carefully remove these from the teeth holding the lid into place. You can now see down into the sides of the drum where items can easily get caught. Take your time and relax this is not hard to do this task. To re-install simply reverse the directions and tighten the brackets back to the body. I hope this helps. If you need a decent diagram go to www.sears.com, click on parts and enter your model number in the search box. From there you can view diagrams, parts and pricing lists. I hope this helps!!! Good luck!

Apr 04, 2008 | Kenmore Oasis 27042 Top Load Washer

1 Answer

Stacking Frigidaire dryer on washer using stacking kit 5303937141


You have to take the top off the washer a put it aside. You no longer need the top. Then you put the two angle brackets on the front top of the washer. this is where the front of the dryer will attach. The back of the washer either has or needs the brackets put on the top (been a long time since I did this). Remove the leveling legs from the dryer. Then lift the dryer and slide it on top of the washer with the back touching the top of the washer and the front about 2 inches higher than the washer top. The back of the dryer slides into the back brackets which are on the top back of the washer. Then lower the front of the dryer and the two "L" brackets on the front top of the washer slide through cracks into the dryer. Pop off the two plastic plugs on the dryer bottom front and place a screw in each one to hold the unit in place. Replace the plastic caps and you are done.

Dec 29, 2007 | Frigidaire FEQ332E Electric Dryer

Not finding what you are looking for?
LG LDF6920ST Stainless Steel 24 in. Built-in Dishwasher Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Dishwashers Experts

Mike
Mike

Level 2 Expert

165 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Mike

Level 3 Expert

4340 Answers

Are you a LG Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...