Question about Yamaha RX-V995 Receiver

Open Question

Remote control disassembly - Yamaha RX-V995 Receiver

Posted by Anonymous on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Clean remote

  • How to Clean a Remote Control ' Cleaning Guides > Cleaning Guides Cleaning the remote is a relatively easy task. However, you have to be extremely careful with it so that you do not damage the battery contacts or the circuits.
  • How to clean a remote control - YouTube
    • 6 MIN
    • ADDED 2010-09-07
    Video embedded ยท Extend the life of your remote control. Fix unresponsive buttons easily by disassembling and cleaning the remote.

  • Dec 30, 2015 | Televison & Video

    1 Answer

    Remot control working but not properly

    Option 1: Purchase replacement remote
    Option 2: Purchase a universal remote
    Option3: Like most remotes they can be disassembled and the board and rubber pads cleaned with de-natured alcohol and reassembled. This may work but is tedious. Unless batteries have leaked in the remote. Then replacement is your only recourse.

    Mar 15, 2014 | Televison & Video

    1 Answer

    Volume control not working properly on my remote control, all other buttons are fine, do I need a new remote or canI get it repaired if so where? Onkyo HT550 unit

    Did u tried disassemble remote control and clean PCB with clean cloth? Also u can take rubber part of remote and wash it carefully in soaped water . While u have it disassembled check for bad solder connections at IR LED on remote controller . Regards .

    Oct 01, 2012 | Onkyo SKS-HT500 System

    3 Answers

    Disassemble or open the remote control Sony RM-YD035

    if Sony Remote RM-YD035 does not change channels or turn off TV, the buttons got dirty coz those are you most used buttons.

    You can repair Sony Remote RM-YD035 yourself. It's quite easy and fast, with perfect result!

    To disassemble or open the remote control Sony RM-YD035, first remove a single screw in the battery compartment. Then use a very thin but strong screwdriver and insert it between top cover and the body at the back part of the battery compartment. Move the screwdriver up and down and slowly move it to the left and to the right and continue along the perimeter. Use two or three such screwdrivers and in 2-4 minutes the top cover plate with buttons will separate from the body/bottom/casing.

    Clean both parts thoroughly. And then gently put them back together in the opposite order. The parts will snap closing.

    You are done.

    Mine is now working perfectly

    Apr 01, 2012 | Sony Rm-yd035 Remote Control

    1 Answer

    My remote control has stopped working ,i have tried new batteries but it not work

    good day... well you said you already replace w/ new battery..try to check the batt. terminals if still intact...if you can disassemble it to clearly check the wires.. if still good I suggest that you replace the infra red LED...goodluck

    Feb 12, 2011 | Abt Television 1745 Remote Control

    1 Answer

    The volume om my jvc remote [ r m - sthc61j ] is not working properly,,what can I do

    i f you know how to disassemble your remote control, you may clean the rubber pads inside, if cleaning wont help, i usually place a small round cut out from an aluminum foil in place of the worn rubber pads switches..

    Feb 09, 2011 | JVC Televison & Video

    2 Answers

    Non functioning "zero" button on Logitech Harmony 880 Rf remote

    The problem may be either a stuck "0" button, or the contact on the control board is dirty. You can take the remote apart by removing the screws and slowly separating the top and bottom halves of the remote. There should be 2 screws on the back of the remote (1 is hidden under the battery/cover). If you need further assistance let me know.

    Oct 31, 2009 | Logitech Harmony 880 LCD Remote Control

    1 Answer

    Sound will not decrease and also menu ok button no longer displays controls for picture & sounds etc

    disassemble the remote. use some alcohol wet paper to clean the printed board and then reassemble

    Oct 25, 2009 | Hitachi HL01453 Remote Control

    1 Answer

    Milk spilled on tv remote controller

    Remove batteries from remote, to avoid further damage caused from liquid on powered circuits.
    Allow the remote with the cover opened to dry for few days. Ideally the remote should be disassembled and the internal parts treated with cleaning solution, or 70% isopropyl alcohol and water. If you do not want to disassemble just let it there to dry up.

    If the remote does not work after that , it means that the liquid had damaged circuits.

    In that case get a replacement remote.

    Replacement Remotes


    TV Remote Controls - UK Replacement Remote

    Aug 26, 2009 | Televison & Video

    1 Answer

    Having problem with my gpx remote control for my

    Try cleaning the remote, the button "5" could be jammed (disassemble the remote, clean the rubber pad(s) with buttons, circuit board AND housing, especially the holes through which the buttons protrude, there may be some stuff keeping the button sticked/jammed).

    You can use ethyl alcohol for cleaning.


    3rq8 (Triarcuate)

    Jul 24, 2009 | Televison & Video

    Not finding what you are looking for?
    Yamaha RX-V995 Receiver Logo

    Related Topics:

    20 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Yamaha Audio Players & Recorders Experts


    Level 3 Expert

    5349 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    The Knight
    The Knight

    Level 3 Expert

    75178 Answers

    Are you a Yamaha Audio Player and Recorder Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides