Question about Mitsubishi WD-60638 DLP TV

Open Question

Has sound know picture

Has sound but know picture also when I turn on power light is green then it turns red

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 146 Answers

SOURCE: Lamp light turns red

Yes this is the signal for a bad lamp. Other things can cause this. 1. Look at the new lamp. make sure it still looks good. not broken with little glass pieaces in it. 2. When you turn on the tv, put your ear to the lower back part of the tv near the middle. Listen for the start up of the color wheel (a low high pitch sound only at the start up of the motor). If this is good you will here a ticking sound only if the lamp dose not light.

Now with all this info. If the lamp lights (as seen from the back of the set) and goes out after a few seconds and you did not here the color wheel spin up, the color wheel is bad.

If you here the color wheel spin up and no ticking sound, the Ballast is bad.

The ballast part no. 939P978010

The color wheel is not avialable from Mits. You will have to replaced the light engine. It cost to much. Just buy a new tv.

Posted on Nov 15, 2008

  • 7 Answers

SOURCE: Mitsubishi WS-65809 turns off right away

check the collector drop on Q29a002. If it is less than 16 nano amps, repl ic u12 in conver circuit. stk392-570 and pico fuses f04 and f05 24v circ

Posted on Jan 14, 2009

Slinteriors
  • 8617 Answers

SOURCE: no picture or sound mitsubishi 62525

Capacitor failure is the most likely scenario the FMT ans Signal PWB would cause the picture interference and the power pwb would cause the lamp light to turn red and give a 34 code when the device/ input and menu buttons are pressed in together and held for five seconds. That chassis has issues with every board in the chassis having failed capacitors you can get repair kits for the V26 chassis at the follwing link that come with instructions. Your model is the V26 chassis. Heres the link.
http://servicemanuals.vstore.ca/

Posted on Jan 26, 2009

  • 453 Answers

SOURCE: No picture with sound

yes , u need a new lamp shop around , cost less

Posted on May 08, 2009

  • 16 Answers

SOURCE: WD-52525 - No picture, green status light then turns to red lamp

check the lamp

Posted on Jun 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed caps power light turns green but no picture or sound


Hi Garry
Hard to say but I suppose if you can change the caps surely you already know about their polarity ;) but I'd double check that and look for cold soldered joints.

Best of luck
XyFinx

Dec 14, 2013 | Televison & Video

1 Answer

42 inch Akai plasma - no pix no sound


i think your power board has some serious problem

May 21, 2008 | Astar LTV-2701 27 in. HD-Ready LCD...

1 Answer

The screen went blank and green light started flashing. Turned off the TV and let it cool. Turned it back on, getting sound but no picture. Red light is on, after about 15 seconds the green light blinks...


Since you say that there is sound but no picture, the first thing I would check would be the status of the lamp. I believe that the lamp has been shattered or the filament is blown. Please verify this and let me know

Feb 25, 2011 | Toshiba 52HM95 52" HDTV Projection...

1 Answer

No sound/picture and red power light always on (Hitachi 43FDX15B)


When u turn the tv on,u hear alot of clicking?That mean the Ballast that help the projection bulb to work is dead.Change the Ballast,might as well change the bulb too.U don't know what is the condition of the projection bulb in.

May 29, 2010 | Hitachi 43FDX15B 43" Rear Projection...

1 Answer

Maganavox flat screen tv no pic, red light blink codes...


Those blinks are fault codes. To know more visit the site linked here. http://electronicshelponline.blogspot.com/

Mar 25, 2017 | Televison & Video

1 Answer

Powers on but no picture or sound


i need a screen off a 47inch magnavox if u coudent fix urs and ur interested in selling me ur screen let me know
(47mf437b/37) noe28cervantes@yahoo.com

Jan 04, 2010 | Toymax Magnavox 47MF437B 47 in. LCD TV

1 Answer

No picture but normal sound.


projection bulb needs replacement

Aug 11, 2008 | Televison & Video

Not finding what you are looking for?
Mitsubishi WD-60638 DLP TV Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Televison & Video Experts

matt martin
matt martin

Level 3 Expert

1210 Answers

The Knight
The Knight

Level 3 Expert

74118 Answers

Jaime Hernandez

Level 3 Expert

2318 Answers

Are you a Mitsubishi Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...