Question about Hunter Ceiling Fan Remote Receiver 85112-01

3 Answers

Hunter ceiling fan remote problem

Ceiling fan remote control 85112-02 will operate light and slow speed only. I can hear it clicking on all buttons but medium and fast dont work.

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

You will most likely need to replace the receiver with a new one from hunter. The receiver is actually a complete controller and contains the receiver, relays (which you hear clicking) and starting condensors(large capacitors which hold a charge that is "dumped" over the windings to get the motor to start from a dead stop). These appear to be pretty tightly assembled unless you have a desire to start replacing parts "off the board."

Posted on Sep 07, 2009

  • Rohan C Feb 28, 2012

    I had this same problem and found that it was the transmitter!!! I opened the back and found the loop antenna dislodged from the circuit board. Soldered it back in and the fan responded to all speeds!!! I guess it was poor original soldering combined with the pressure on pressing the buttons. Try this before you buy a new receiver/transmitter. Rohan

×

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 632 Answers

Check contact pads..

Posted on Jun 20, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 11 Answers

Fixed My Hunter remote controlled ceiling fan, started not controlling the light, then later the fan quit also. Start by
testing the remote buttons, see this post... http://www.fixya.com/support/t11813083-cp9430r

Posted on Aug 27, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My hunter ceiling fan turns very slow


Check your capacitor. If this is an add on remote, set the fan on high with the remote then pull the chain on the fan until you get high speed.

Sep 17, 2014 | Hunter 52" Ceiling Fan With Light And...

2 Answers

Hunter fan 27227 remote stopped working


How i fixed my Hunter #28096 remote controlled ceiling fan, started not controlling the light, then later the fan quit also. Start by testing the remote buttons, see this post... Cp9430r Fixya

Jun 22, 2014 | Hunter Ceiling Fan Light Remote Control

1 Answer

Remote will not turn on fan. A ll I get is a click.Light works fine


How i fixed my Hunter #28096 remote controlled ceiling fan, started not controlling the light, then later the fan quit also. Start by testing the remote buttons, see this post... http://www.fixya.com/support/t11813083-cp9430r Cp9430r Fixya

May 30, 2014 | Hunter Ceiling Fan Light Remote Control

2 Answers

Hunter ceiling fan remote 27144


reset the code and test again.
God bless you

Feb 18, 2013 | Hunter 27144 Universal Remote Controls...

2 Answers

Hunter ceiling fan model 23530-300


the roll was rusted maybe .you can take apart it for checking .
ceiling light

May 01, 2012 | Hunter Ceiling Fan Remote Receiver...

2 Answers

Fan with remote control speeds up on its own


bring the remote control to the store and have its function tested with similar unit. if the control works fine then you have no choice but to take down the fan and have it repaired

Oct 18, 2009 | Hunter 52" Ceiling Fan With Light And...

1 Answer

HUNTER ceiling fan remote works with fan but not light


Unfortunately, you either have a faulty reciever or remote. A replacement will cost $30-$40 at homedepot2.gif. And it doesn't matter which is faulty because you can't purchase them seperately anyhow.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jerry_612d8419f8984578

Sep 08, 2009 | Hunter Fan Co. 60 In.Brushed Nickel...

1 Answer

Ceiling fan remote will not turn on light


common problem , i went to home depot and bought a new remote for my hunter fan , and it worked again , salesman was very knowledgeable and helpful . thanks. explain the problem to him , he can help .

Dec 28, 2008 | Hunter 52" Ceiling Fan With Light And...

1 Answer

Hunter ceiling fan


Sounds like the remote receiver units (located where the mains connect to the fans) took a surge and have failed.

Jun 16, 2007 | Hunter Ceiling Fan Control Switch

Not finding what you are looking for?
Dryers Logo

Related Topics:

5,818 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hunter Dryers Experts

Paul Bade

Level 3 Expert

1606 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14423 Answers

Are you a Hunter Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...