Question about Canon PowerShot A570 IS Digital Camera

Open Question

Camera won't turn on - Fuse location(s) needed

Pretty sure a student blew a fuse on one of these. Rather than toss it, I'd just as soon bridge the fuse with a jumper block. Anyone know the location of the fuse(s) on this model?

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

drifterK
  • 4924 Answers

SOURCE: i have a canon powershot

the drive P fuse is the fuse of the camera motor..and for to change it you have to open it ..there for I will not advice you to do it by yourself ..but take it to someone that really knows what is doing ..The part itself is not that expensive ..but the hand work may cost a little ..

Posted on Aug 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lc320em2f I bought a new fuse and as soon as I plugged it in the fuse blew. What can I do? Where can I get a new fuse?


you have a short most likely in the power supply. Replacing the fuse won't solve your problem. Get the set diagnosed

Sep 08, 2012 | Acer Televison & Video

2 Answers

My son tried to plug in a fuse (not even sure he plugged it into a fuse) and blew the fuse for the power windows and locks...where do i find the fuse box for these?


Improve the FixYa experience for everyone by voting.

There is one fuse box located under the dash on the drivers side above the gas and brake pedal. The second fuse box is located in the engine compartment on the drivers side close the the headlamp.

The exact fuse should be etched on the fuse box lid, on the top or inside the lid. If not, it will be in the owner's manual.
5_9_2012_9_46_33_pm.png

May 09, 2012 | 1997 Ford Windstar

2 Answers

My kenwood KAC-7204--- the wiring is hooked up right, I just got a 2000 watt max sub 1000 watt rms, i was running the amp in bridge mode and it ran for 1 day than it turned off. I checked it and the fuse...


when i was running my sub off bridge mode this kept happening to me. I ended up just running two subs and for some reason the fuse stopped blowing. i think there is something wrong with these amps.

Jun 04, 2011 | Kenwood KAC-7204 Car Audio Amplifier

1 Answer

No rear lights and dash lights


im pretty sure you blew a fuse. you can change it yourself by just finding out where your tail light fuse is located and buying some at walmart for $3 or so

Oct 23, 2009 | 1995 Ford Escort

1 Answer

No Power


all sets must have rated fuse for protection. some units now use what is called a PICO-FUSE.this type of fuse is soldered into the pc board. usually marked with location i.d. F301,F901,F400. etc. these fuses look like resistors or in-line coils. check continuity w/ohm meter. if new fuse blows as soon as you plug in tv, suspect bridge diode ciruit or main filter cap(large ripple filter by main fuse. if new fuse blows when you try to turn on, suspect 130v regulator or high voltage short(horizontal-output, flyback transformer) good luck!

Feb 20, 2009 | Televison & Video

1 Answer

Tryed to bridge


You probably blew the output transistors and if you did then the amp is as good as dead. Not worth it to fix just replace it.

Jun 04, 2008 | Phoenix Gold Ti500.4 Car Audio Amplifier

4 Answers

No power


I too replaced my bottom LCD with an aftermarket part and blew the fuses. I followed L1Cupids's advice and fixed mine. You have to solder F1 & F2 fuses. The insructions from the internet say to bridge the fuse with a wire. Well, it is only a 1/16 of an inch...I found this to be impossible. I just bridged the fuse with the solder iteself. If you need the instructions look here:
http://m3wiki.com/index.php/Nintendo_DS_Lite_:_Repair_a_broken_console_(blown_fuse)

~Julie

0198e98.jpg

Nov 11, 2007 | Nintendo DS Lite Console

Not finding what you are looking for?
Canon PowerShot A570 IS Digital Camera Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Canon Cameras Experts

kakima

Level 3 Expert

102366 Answers

TC CAMERA REPAIR.Com...

Level 2 Expert

169 Answers

old marine
old marine

Level 3 Expert

1973 Answers

Are you a Canon Camera Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...