Question about Asko 24 in. D3250 Built-in Dishwasher

1 Answer



Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

First of all, if you've turned off the Correct power source it would stop running. Keep trying to find the correct circuit breaker. The power must be discontinued and let the dishwasher sit for at least 5 minutes so it can "forget" the program. However, if the same program comes back on, then I suggest holding down the heavy wash symbol continually for several seconds. Or perhaps holding down the cancel symbol for several seconds instead. It sounds like the heavywash symbol is stuck or broken behind it's cover. If the symbol was "jiggled" alittle to the right or left it may become "unstuck". Hope some of this helps you.

God Bless You and your family,

Miss Midget

Posted on Nov 02, 2007


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My name is raza. i have west point washing machine model no 1225tl , Fix error LE is coming. please tell me about this urgent.

An LE error code on the washer's display indicates that the motor is locked, possibly due to a heavy wash load.
Large and heavy sized loads will put a strain on the motor, causing the LE code to occur. Performing a reset on the washer will normally resolve this error.
To reset the washing machine:
  1. Press POWER to turn the washer off
  2. Unplug the washer from the power outlet. If the outlet cannot be reached, turn the circuit breaker to the unit off.
  3. With the power disabled to the washer, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.
The washer should now be reset and the LE code cleared. If washing a heavy or large load, reduce the load size and attempt to restart the cycle.
Note: For your safety and to preserve your warranty, if the issue persists, LG recommends that all repairs are performed by an Authorized Service Center.

Jan 06, 2017 | Washing Machines

1 Answer

Wont work when turn on motor will only do hummm

The motor is stuck and not turning. Do not power on and locate source of problem. Could be bad motor bearings or something in the power chain causing the problem

Aug 02, 2015 | Speed Queen 3.3 Cu.Ft. Heavy Duty Top Load...

1 Answer

Normal, heavy, delicate lights stuck on--cant power on or off

If you have tried to unplug from mains power and there is no difference then you will need to provide the actual model number of your dishwasher in comments field.
The Samsung error codes for Normal, Heavy , Delicate lights stuck is not listed. The closest is Normal, Heavy, Quick which relates to a Low Water level. Also confirm which lights are stuck in your case and whether these are flashing or not.

Apr 17, 2014 | Samsung Dishwashers

1 Answer

Stucked motor???

You most likely will need a tech who can go more in depth with it. One that can come to your home.

May 28, 2012 | Whirlpool Washing Machines

1 Answer

Hi....f 13 is flashing on the machine and a red spanner symbol is on all the time, also unable to open machine even after draining it manually... thanks for any help you can offer.

You did not say what machine you have!
F 13 I have is a dispenser circuit error and the causes/procedures are
1 Unplug the washer or disconnect power
2 Check the mechanical linkage from the motor to the top of the dispenser
3 Check the wire harness to the dispenser motor and the central control unit
4 Check the dispenser motor for powered rotations

Replace faulty components

If there is a spanner symbol lit it means you need to call a repairman.

Feb 17, 2011 | Washing Machines

1 Answer

I am using a candy cty 105 smart. The machine doesnt seem to finish the cycle I washed at 60 and at the end the symbol for heavy solied flashed and the start symbol flashed. I havent used the machine...

i had this problem to.. my solution for this was the wire of pump. wire was just unpluged i just re entered the wire end all was back to normal.. :P

Jan 24, 2010 | Candy Washing Machines

1 Answer

I have a Frigidare washer/dryer combo (model # FLEB8200DS0). My wife washed a heavy load and the washer stopped draining completely. Agitator works fine. Please HELP...

I'm not sure if the heavy load had anything to do with it or not. this unit has a remote pump, which means the pump doesn't run off of the main belt . It actually has a motor of it's own. Basically you would have to remove the front access panel, of course unplug from power, make sure the pump will turn. with the power off you can rotate the cooling fins on the pump motor. if it turns freely then you would have to determine if the pump motor is getting power. If it is getting power then you need to replace the motor.

Oct 24, 2009 | Frigidare FEF336EC Stainless Steel...

2 Answers

My daughter put a big blanket int he washer. it started and then after a few minutes it stopped. I had to untangle the blanket after the motor stop working. now it will not even turn on. I am thinking

Hi, When the washer is in spin mode, do you hear the motor running at all. It could be the lid switch has broke. I do not believe it will be a motor.
To test the lid switch, Remove the screws located on the back of the control panel on each end.
Lift the control panel and let it rest on the hinges. The lid switch is located to the left and has a three wire harness. Unplug the washer before you unplug the harness and put an insulated wire between the two gray wires (not the green stipe wire)
If you can jump this, turn the timer back into spin cycle and see if it starts.
Please let me know if it helps or if I can assist you further.


May 30, 2009 | Whirlpool LSR5132PQ Top Load Washer

1 Answer

Kenmore Series 80 top loading washer that doesn't spin or agitate

Unplug machine, remove water pump and motor, behind the motor is a coupler, take broken parts to your local appliance parts store. Costs 16 bucks, replace the broken parts with new ones, reassemble machine. Never ever do a blanket/comforter in your machine again!!

Mar 31, 2009 | Kenmore 24032\24036 Top Load Washer

2 Answers

Fault f13

Hi. F13 indicates dryer fan motor or thermistor problem
If you can't hear the fan motor running on the dry cycle then it is probably faulty.
Hope this helps.
Please feedback.

Nov 13, 2008 | Hotpoint Aquarius WD640 Front Load...

Not finding what you are looking for?
Asko 24 in. D3250 Built-in Dishwasher Logo

Related Topics:

361 people viewed this question

Ask a Question

Usually answered in minutes!

Top Asko Dishwashers Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

John Tripp
John Tripp

Level 3 Expert

4655 Answers


Level 3 Expert

78919 Answers

Are you an Asko Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides