Question about Panasonic DECT 6.0 Expandable Cordless Phone System with Digital Answering System

Open Question

No link to base ...reconnect ac adaptor comes up when I press talk

What do I do to fix

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 514 Answers

SOURCE: push the talk button and it said no link to base reconnect ac ada

go to page 35 of the manual ("http://service.us.panasonic.com/OPERMANPDF/KXTG1032.pdf" if you don't have it) good luck!

Posted on Feb 22, 2009

Ad
Coleman37
  • 337 Answers

SOURCE: phone says no link to base phone stop working

Try unplugging the base unit and plugging it back in again. This is not guaranteed to help but has worked in the past.

Posted on Feb 28, 2010

cadillac02
  • 318 Answers

SOURCE: When I press the talk

Hand each phone up on the base and it will marry it. If you continue to have no link to base make sure everything is plugged in correctly. If it persists you probably have a defective phone.

Posted on Jan 25, 2011

  • 4 Answers

SOURCE: Says No Link...Reconnect base AC Adapter

Disconnect the AC adapter from the unit, wait for 5 seconds, then reconnect. The plug may have become loose over time or not be fully inserted. If that does not work, try re- registering the handset.
To re-register, see screenshots attached. pianistas.png pianistas_1.png

Posted on Mar 06, 2011

SOURCE: "No link to base, reconnect

Disconnect the AC adaptor from the unit, wait for a minute, then reconnect. The plug may have become loose over time, or not fully inserted. If that does not work, try reregistering the handset, another handset may have deregistered this handset.Initially, the displayed message indicates that the base is not receiving power. Verify that the base is lighted up / powered on.Try a full hard reset on the Panasonic KX-TG9333T by disconnecting the power and telephone line connection to the base and remove the batteries of the 3 handsets. Allow unpowered, disconnected condition for an extended period of time (6-8 hours). The idea is to force the system to revert back to factory defaults.Reconnect the KX-TG9333T and the batteries to the handset. Recharge if necessary. Go through the initial set-up procedures.

Posted on Aug 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

One of the phones gives the message "No link to base. Reconnect main base AC adaptor.


If other phones are working with this base, then you may need to register the phone with the base. You will have to check your manual for how to do this. Some phones have it on their menu and some do it by simply placing the phone in the base unit. I'm not sure what model you have or how old your system is. Hope this helps. Good luck!

Mar 02, 2010 | Lands Phones

1 Answer

There is no dial tone. cannot call out or recieve calls


• Check both ends of the base unit telephone line cord.
• Make sure the AC adapter is plugged into the base unit and wall outlet.
• Disconnect the AC adapter for a few minutes, then reconnect it.
• Reset the digital security code
• Make sure TALK is pressed.

Jan 26, 2010 | Uniden 5.8GHz Cordless Phone

1 Answer

Push the talk button and it said no link to base reconnect ac ada


go to page 35 of the manual ("http://service.us.panasonic.com/OPERMANPDF/KXTG1032.pdf" if you don't have it) good luck!

Feb 16, 2009 | Panasonic KX-TG1033S Cordless Phone

1 Answer

Uniden Power Max 5.8 - (TRU8880-2)


1. Disconnect Battery from handset(s)
2. Disconnect Phone Cord from wall jack
3. Disconnect Phone cord from base unit
4. Disconnect AC adapter from wall outlet
5. Allow to sit for 30 min
6. Reconnect Phone Cord to base
7. Reconnect Phone cord to wall jack
8. Reconnect AC Adapter to wall outlet
9. Reconnect Battery to hanset until you click or feel the plug snap into place
10. Re-Register Handset by placing on main base in most instances.

please rate this post

Aug 04, 2008 | Uniden 5.8GHz Dual Cordless Phone

1 Answer

Cordless phones display "No link to base.Move closer to base", when an attempt is made to make a call.


Used online phone manual/troubleshooting section to resolve issue. Disconnected AC Adaptor from electric source and reconnect to reset. Problem solved.

Feb 23, 2008 | Lands Phones

2 Answers

STILL SAYS "PLEASE REGISTER"


I think this may be the answer. With multiple handsets reading "Please register" and a "working" base station (w ith dial tone). If you bring the remote units to the base station and place them on hte base, they will register and stay registered after you return them to the remote base. It doesn't say this anywhere in the instructions as it gives you the impression the remotes will register from their own base.

Jan 04, 2008 | GE 25932 Cordless Phone

Not finding what you are looking for?
Panasonic DECT 6.0 Expandable Cordless Phone System with Digital Answering System Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Panasonic Lands Phones Experts

kakima

Level 3 Expert

102366 Answers

guyvstewart

Level 2 Expert

83 Answers

george  peters
george peters

Level 3 Expert

860 Answers

Are you a Panasonic Lands Phone Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...