Question about Jl Audio Car Audio & Video

Open Question

Box blueprints rebuild a 10w6v2 jl audio

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: jl audio 10w6 x zapco350

These subwoofers are dual 4 ohm voicecoils.

Parallel wiring the 2 voicecoils would net a 2 ohm mono load.

Connect both + on the sub to the + on the amp.
Connect both - on the sub to the - on the amp.

Many professionals simply jumper the 2 + and 2- on the sub.... then run 1 set of wires from one of the terminals to the amplifier.


42af0be.jpg
Thank you for using FixYa - a FixYa rating is appreciated!!

Posted on Jan 27, 2009

  • 18 Answers

SOURCE: i need to build a box for a jl audio 12 w 3 and i ...

all the sub specs should be on their web site.

Posted on May 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can i rebuild a jl audio 10w6v2 and how do i do it


check Amazon for replacement speaker foam kits. Just type in your speaker model followed by repair kit and some should pop up. I replaced my infinity foam a few weeks back with no problems.

Apr 20, 2014 | Car Audio & Video

1 Answer

Box size for jl audio 12"w6 going in large trunk


call jl they will give you BEST box recommendation

Jan 24, 2013 | Car Audio & Video

1 Answer

One sub not working


Try this....the speaker that is not working, gently work the cone up and down with you fingers. Be careful not to go right thru the cone. One hand underneath(near webbing) and one hand on top over the dust cover. If you hear any kind of scratching, or noise, or it's not "breathing" freely, then the voice coil of that speaker may have overheated, or the speaker has extended above and beyond its range of movement (called excursion). And may as well be blown/dead/fried..however you want to say. I hope this is not the case for you.

Apr 26, 2010 | Jl Audio 10W6v2 Car Subwoofer

1 Answer

How to run wires is series fof 3 subs


If they are single voice coil speakers (1 positive and 1 negative terminal on each speaker) then connect from amps' Positive output terminal to spkr. 1 positive terminal, THEN spkr. 1 neg. terminal to spkr. 2 positive terminal, THEN spkr. 2 negative terminal to spkr. 3 positive terminal, THEN spkr. 3 negative terminal to amps' negative output terminal.

That is 3 speakers wired in series. if each spkr is 2ohms, then you will have a total 6 ohm load. If 4 ohm spkrs., then a total 12 ohm load, if 8 ohm spkr., then a total 24 ohm load.

Be careful because amps do not like these odd ohm load totals. You might get away with a 6 ohm total load. Depends on the amp.

Mar 27, 2010 | Jl Audio 10W6v2 Car Subwoofer

1 Answer

Have a Jl 500/1 installed Sat was slappin good puushin 10W6V2 high output box with rockford 1 farad cap. any way blew somethin smelled it amp still green no sound is only thing! sub still works checked on...


Check your stereo first. make sure the speaker outs still work if yes, the check your amp. If you know the signal is getting to the amp and not out to your subs, then your amp is blown. The high voltage transistors inside the amp usally are the ones that go out. Just open it up and if you smelled something, you can probably see it.

Mar 11, 2010 | Car Audio & Video

1 Answer

I need to find a good sub box for my 10 inch JL w6


Hello ama1228a,

You did not say what type of vehicle the box is to be mounted into. Many times, where the box goes dictates the shape and size you have to work with.

That JL W6 will work OK in a sealed box with as little as .625 CuFt of volume and a ported box with .75 CuFt, so you have lots of choices.

Here's a link to the PartsExpress box page. These are Goldwood boxes, so don't let the prices scare you away. They really are built well, and one of them will make your JL sound good.

http://www.parts-express.com/wizards/searchResults.cfm?FTR=&search_type=main&WebPage_ID=3&searchFilter=goldwood+boxes

Hope this helps.

Apr 02, 2009 | Jl Audio 10W6v2 Car Subwoofer

1 Answer

Jl audio 10w6 x zapco350


These subwoofers are dual 4 ohm voicecoils.

Parallel wiring the 2 voicecoils would net a 2 ohm mono load.

Connect both + on the sub to the + on the amp.
Connect both - on the sub to the - on the amp.

Many professionals simply jumper the 2 + and 2- on the sub.... then run 1 set of wires from one of the terminals to the amplifier.


42af0be.jpg
Thank you for using FixYa - a FixYa rating is appreciated!!

Jan 27, 2009 | Jl Audio 12W6v2 Car Subwoofer

Not finding what you are looking for?
Car Audio & Video Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jl Audio Car Audio & Video Experts

Mark Skinner

Level 2 Expert

77 Answers

Tygh Duval
Tygh Duval

Level 2 Expert

300 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Are you a Jl Audio Car Audio and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...