Question about HP DesignJet 430 InkJet Printer

1 Answer

My HP Designjet 430 plotter is old but works well it always has had the cartrage and data light on but it would always still work. i have tryed to fix it with no luck. When i try to load the paper it will spool then when i flip the lever down to align the paper and then flip it back up it aligns then it cuts the paper strait then it will wait a minute and unspool the paper this is driving me crazy.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers

Could u plz tell me that Ready Led is also on along with these two leds , if yes then replace cariage assy
u can shre detailed prob at my email id

Posted on Sep 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When you turn on my hp 430 desinejet printer the light comes on in the error group that says media


on this machine ( v old) if the drive belt has chewed then the plotter will not even come to ready instead it makes a few clunks and flashes lights - If this accurately describes your error then you will need the drive belt replacing, however this machine is now so old that getting hold of new unused parts is nothing short of a miracle Good luck with that one!

Feb 11, 2014 | HP DesignJet 430 InkJet Printer

1 Answer

Hp Designjet 430 new black cartridge printing blank page


Blocked print head nozzles
Inkjet printers need to be used frequently to prevent blocked print head nozzles. You may have blocked print head nozzles.
Try the printer maintenance to clear the printer nozzles.
After several deep cleaning attempts and there is no improvements in the print then a new print head is required.
A new print head maybe expensive and it maybe more cost effective to purchase a new printer.

Oct 22, 2012 | HP DesignJet 430 InkJet Printer

1 Answer

HP DesignJet 430 wont accept media


Hi,
This is the problem with the sensor. It tries to read the size of the paper, the sensor is on the side of the carriage assy(cartridges are installed on this assy). You can try cleaning this sensor or get it replaced or some times the service center will replace the carriage unit as a whole.

Dec 01, 2009 | HP Office Equipment & Supplies

1 Answer

HP DesignJet 430 rejecting media


When you load the paper, the carriage edge detector measures exactly where the right edge of the paper is located. Then the paper is rolled forward and the edge is measured again. If there is a difference in the measurements, the printer assumes the paper is not loaded squarely and rejects the paper. After you load the paper and the printer asks you to align the paper, take your time, release the paper with the release lever, and line up the right edge of the paper with the right edge of the paper roll. You might have to do it more than once to get it to load. Some plotters are very sensitive and others are more forgiving.

Sep 25, 2009 | HP DesignJet 430 InkJet Printer

1 Answer

Data & cartriege light on


the problem is caused by the TRAILING CABLE (RIBBON CABLE THAT GOES FROM CARRIAGE ASSY TO MAIN LOGIC BOARD)
REPLACE IT AND YOU WILL HAVE A LIKE NEW WORKING PLOTTER.....CHEERS.

Sep 13, 2009 | HP DesignJet 430 InkJet Printer

1 Answer

Hp plotter designjet 1055 CM plus plotter produces system error


one of the printheads is bad.....check the error code again,because 060308 does not exist in hp designjet 1055cm plotter.

Jul 31, 2009 | HP Office Equipment & Supplies

2 Answers

450c color problem


The 430 ID is B/W, you need to load the 450C driver to get color, renaming the driver isn't enough.

Oct 13, 2008 | HP DesignJet 450c InkJet Printer

1 Answer

Request for designjet plotter info


my hp 450c plotter works properly in vista. First I' ve tried unsuccesfully to add new printer through windows menu. Then through Autocad menu (plotter manager) I added the specific plotter.

Jul 09, 2008 | HP DesignJet 450c InkJet Printer

1 Answer

Hp designjet 430


This usually is solved by removing and reinstalling the ink cartridges...make sure the electrical contacts are clean (use a dry paper towel) on both the print cartridge and the carriage.

If the error still happens then the carriage or trailing cable are bad and will need replaced.

Nov 28, 2007 | HP DesignJet 430 InkJet Printer

Not finding what you are looking for?
HP DesignJet 430 InkJet Printer Logo

378 people viewed this question

Ask a Question

Usually answered in minutes!

Top HP Office Equipment & Supplies Experts

mukhtar21 shaikh
mukhtar21 shaikh

Level 3 Expert

2022 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Les Dickinson
Les Dickinson

Level 3 Expert

18425 Answers

Are you a HP Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...