Question about Rheem Water Heaters

Open Question

Rheem pvs40-36fv no hot water

It has blinking lights on side 2 short than 3 short blinks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: I have a rheem rgdg

i have a rdgd-075auer series that I am looking for the manual or blueprint to install the board on it.

Posted on Jan 17, 2009

Ad
dragonsthatk
  • 547 Answers

SOURCE: blinking red light,

It seams alot of people have this same problem All must get ahold of manufacturer and report this it must be there pump's thank you for useing fixya

Posted on Feb 17, 2009

odiebugs
  • 949 Answers

SOURCE: No hot water from tankless water heater. Bliniking Readout

http://www.rheemtankless.com/content/tankless/rheem/help.shtml

This is there website.Above.
Use the live chat to ask them, the code you listed does not seem to correspond to there code list, the only code that does is code 76,
which is a problem with the remote control not talking to the unit.
So your best bet is to tell them the error.

Posted on Apr 07, 2009

  • 2 Answers

SOURCE: My Rheem Tankless Hot Water Heater is installed, but is it not attempting to start. The digital display keeps blinking 82, 0, 82 , 0 ...?

If this is a new board and Altidude chip with power on set dip switch 1 and 2 to on. Then press and hold adjust button until on board blinks fast then and you will see dashes on LCD display. Set dip switches 1 and 2 back to off. Turn on remote unit and you should see 100F. With any luck you are good to go.

Posted on May 30, 2009

gary1121
  • 332 Answers

SOURCE: PVS50 rheem power vent water heater do not reignite/restart/kick

I actually just installed one of these the other day, I found that the ignitor wires were straped to the gas inlet and they were shorting out,, I wraped them with electric tape and the unit came on and stayed as for the thermostat make sure your flue is clear of all obstuctions even outside, make sure on the vent on the top back of the unit is clean and no lint or dust has built up on it, you can take a small soft brush and just sweep it across it

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Protech 62-24084-02 troubleshooting


62-24084-02 LED CODES
POWER LED - GREEN
ON - Normal
OFF - No power to board
OK LED - GREEN
One Blink - One hour retry delay
Two Blinks - Pressure switch failure (remains open)
Three Blinks - Limit switch fault
Four Blinks - Pressure switch failure (remains closed)
Five Blinks - Twinning fault
FLAME LED - YELLOW
ON - Good flame
Rapid Blink - Flame present with gas valve de-energizing
Slow Blink - Marginal flame

Jan 01, 2014 | Protech Rheem/62-24084-82-1PK - Integrated...

1 Answer

Why is the controller UMC-117 keeps blinking c8?


C-8 error codes could mean anything from the fan not starting, a bad control board, or a blown capacitor. Best bet would be to call Rheem customer service and they'll ship part or suggest licensed contractor to troubleshoot and replace what's necessary.

Open following link to view fixya questions on 1 model of Rheem tankless
Some older questions have information that is useful, and varied
http://www.fixya.com/tags/rtg_74pvn

Open typical manual to review required regular maintenance for tankless on page 29
The word maintenance is used throughout manual, indicating that tankless are a yearly budget nuisance
http://waterheatertimer.org/pdf/Rheem-RTG74IndoorOutdoor_owners.pdf

All costs are money.
You can also add simple tank-type water heater that can be turned on when tankless is on the blink.
http://waterheatertimer.org/How-to-install-gas-water-heater.html

Mar 02, 2011 | Rheem Tankless Hot Water Heater...

1 Answer

RHEEM 50 GALLON WATER HEATER,4 BLINKS THEN 2 BLINKS ,ECO FAILURE,UNPLUGGED HEATER STARTS UP AGAIN THEN FAILURE OCCURS AGAIN.


That is a power vent failure code.
Rheem is aware of this problem and are changing systems as we speak. Call your Rheem dealer and demand the updated system.

Feb 07, 2011 | Water RHEEM 40 Gallon FVR PROP PWR Heater...

1 Answer

Paloma (Rheem) tankless water heater 7.4 gpm 199,000 btu outdoor unit. Red light is blinking on pc board. unit fires up for approx 2 seconds then shuts off, then cycles once more for 2 seconds and shuts...


i think your flame sensor is bad but you will need to confirm that with rheem i am unsure what the c7 is for but code 12 is flame failure and there could be carbon build up on the flame rod...

Aug 06, 2010 | Rheem Tankless Hot Water Heater...

1 Answer

No hot water


contact rheem you probably have a circuit board problemb

Jul 24, 2010 | Rheem Tankless Hot Water Heater...

2 Answers

1 unit intermittently shuts off and other won't ignite


if you have the exhaust run together it will not light up,, they have to be seperate,, the computer board sences the unburnt gasses and will not allow it to start,,

Jun 24, 2009 | Rheem 40 GAL ELEC TALL Water Heater 6YR SC...

2 Answers

My Rheem Tankless Hot Water Heater is installed, but is it not attempting to start. The digital display keeps blinking 82, 0, 82 , 0 ...?


If this is a new board and Altidude chip with power on set dip switch 1 and 2 to on. Then press and hold adjust button until on board blinks fast then and you will see dashes on LCD display. Set dip switches 1 and 2 back to off. Turn on remote unit and you should see 100F. With any luck you are good to go.

May 02, 2009 | Rheem Tankless Hot Water Heater...

1 Answer

No hot water from tankless water heater. Bliniking Readout


http://www.rheemtankless.com/content/tankless/rheem/help.shtml

This is there website.Above.
Use the live chat to ask them, the code you listed does not seem to correspond to there code list, the only code that does is code 76,
which is a problem with the remote control not talking to the unit.
So your best bet is to tell them the error.

Apr 07, 2009 | Rheem Tankless Water Heater Main Remote...

Not finding what you are looking for?
Water Heaters Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rheem Water Heaters Experts

Donni Steen

Level 3 Expert

659 Answers

gizmonix

Level 1 Expert

13 Answers

Brad Brown

Level 3 Expert

15639 Answers

Are you a Rheem Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...