Question about Pool & Spa

1 Answer

Balboa spa codes

Dr on top side control

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 717 Answers

I found a listing of error codes on this website for you.

Posted on May 01, 2014


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Ian  Hot Tub
  • 77 Answers

SOURCE: looking for manual tech info on balboa spa control

If you have a user manual check the filter duration isn't set to continuous.


Posted on Apr 17, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where may I obtain a schematic diagram for Balboa Spa control board H716R1A

Probably the only one who can provide you is the distribuitor of the board.

Nov 13, 2014 | Balboa Instruments BALBOA BOARD 100 MORGAN...

1 Answer

How do i get my spa out of sleep mode

It would help to know what spa you have, but the most common controls out there are manufactured by Balboa Instruments. If your top-side controls only have four buttons try pressing "temp" or "set" button followed by "light" button. Once there, pressing the "light" button usually cycles through the programming. On some models the "temp" button must be pressed to confirm the selection.

Sep 14, 2014 | Pool & Spa

1 Answer

Balboa VL700S control panel jets 1 not working

Your problem is going to be in the circuit board in the spa control box under the skirt.
You have a bad relay.
US Parts Center

Jun 25, 2013 | Pool & Spa

1 Answer

Spa pumps are running but display is not lit and nothing I touch on the controls work

This means your top side control is dead, the spa will continue to operate itself in an economy/maintenance mode to prevent damage.

Nov 19, 2012 | Balboa Instruments Duplex Digital Panel 2...

1 Answer

I have a Balboa VS500Z . The circuit board burned up where the heater buses are located . I replaced the board and the heater . Know when I start the Spa it primes at low speed for about a minute . Then...


DR code - Inadequate water detected in heater.
HL code - Hi Limit, Spa over heat. In your case the Hi Limit is preventing the element from burning out.

This means there is no water or not enough water flowing through the heater.
Common causes:
Hi Limit sensor failure.
Blocked suction, skimmer.
Are the gate valves all the way open/up?
Pump is not functioning correctly, impeller/wet end failure.
These are the most common, but there are also other causes.

I hope that helps

Feb 20, 2012 | Garden

Not finding what you are looking for?
Pool & Spa Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pool & Spa Experts

Jay Finke
Jay Finke

Level 3 Expert

1358 Answers

Bill Jordan

Level 2 Expert

372 Answers

David Spradling
David Spradling

Level 3 Expert

5922 Answers

Are you a Pool and Spa Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides