Question about Rinnai Toyostove Direct Vent Heater: Toyostove Laser 73 Shipping

Open Question

Have a code ee2 I have fuel does not ignite

Yes I have fule , it tryed to ignite but didn't now it has the code ee2

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 17 Answers

SOURCE: I have an error code of EE2. The system will not

First- do you have enough fuel.
Does the unit ignite or not
More info would help me
Total Toyo
(907) 488-9179

Posted on Dec 15, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

After my stove runs about two cycles, it shows E E 2. we relight and it ignites and then shuts back down with the error message. The tank is full, no air in the fuel line or filter. suggesations?


Has this unit been serviced. Sounds like the Flame Sensor is dirty and not sensing flame OR this actually isn't any flame due to an ignitor or fuel issue. Here is a complete explanation and diagnosis of the EE2 problem: Toyostove Error Code EE2

Feb 07, 2016 | Rinnai Toyostove Direct Vent Heater:...

1 Answer

Lazer 30 error 22 on panel


The stove quit three times with an ee2 message. The stove is trying to save you from flooding. You may have a fuel problem that is causing the ee2 problem. After three time the stove locks out and won't let you try again. Find out whats up with the fuel. Unplug the heater for 20 minutes and you will be able to try again. Also make sure the igniter is getting hot. Two red wires going into the burner should get hot.

Tom

Sep 25, 2010 | Rinnai Toyostove Direct Vent Heater: Laser...

1 Answer

My toyo lazer 30 won't start, and the EE2 problem comes up.


With an EE2 message you have a problem with the stove igniting during start up. If you continue to try you will end up with an EE22 and the stove will be locked out. If so, un plug for 20 minutes. While you are waiting check out you fuel system. Low fuel, no fuel, dirty filter on tank and stove. Be sure to bled the air off the top of the filter when you change it.

Keep us posted.

Tom

May 14, 2010 | Rinnai Toyostove Direct Vent Heater: Laser...

1 Answer

Lost manual stove is blinking code ee2


No ignition. Check the igniter by feeling around the two red wires when you try to start the stove. They will get very hot so be careful. If the igniter gets hot you have a fuel problem. No fuel, low fuel or dirty filter.

Keep us posted,

Tom

May 10, 2010 | Rinnai Toyostove Direct Vent Heater:...

1 Answer

I have an error code of EE2. The system will not


First- do you have enough fuel.
Does the unit ignite or not
More info would help me
Total Toyo
(907) 488-9179

Dec 15, 2009 | Rinnai Toyostove Direct Vent Heater:...

1 Answer

Gettin an EE2 error - replaced the fule filter at the tank, removed and cleaned the sump screen, no luck. Does the sump screen on this stove fit into the sump with the open aspect of the screen facing the...


The open end goes toward the back of the heater.

Next try cleaning the flue.

Other potential causes for an EE2 are malfunctions of the circuit board, flame sensor or or fuel pump.

-Helping Hands Services
Fairbanks, Alaska

Oct 11, 2009 | Rinnai Toyostove Direct Vent Heater:...

1 Answer

L60AT wont relight


EE2 means no ignition. It could be No fuel or low fuel, dirty filter. You need to look at the flame when you try to start the stove. If you have flame then the igniter is good. If there is no flame and a bumping noise you have a fuel problem. No flame and no bumping you may have an igniter problem. Feel around the burner pot to see if it gets hot. A bad igniter will lead to a flooded stove if you continue.

Tom Hawkins
Bethel, Alaska

Dec 23, 2008 | Rinnai Toyostove Direct Vent Heater: Laser...

1 Answer

EE2 code for toyo laser 56


Hi sammysamual,

My business is Laser Heating Service in the North Pole/Fairbanks areas of Alaska. An EE2 error code is usually fuel related. What does your Toyo do before the EE2 code shows up? If you let me know the sequence of events, I can trouble shoot the problem for you. toyotech

Dec 13, 2007 | Rinnai Toyostove Direct Vent Heater: Laser...

1 Answer

EE2 code for toyo 56


Hi sammysamual,

My business is Laser Heating Service in the North Pole/Fairbanks areas of Alaska. An EE2 error code is usually fuel related. What does your Toyo do before the EE2 code shows up? The firing process is the burner button blinks green for 7-9 minutes, then it clicks up to the medium, yellow light which starts flashing. That is when the fuel pump starts pumping. If you hear a fairly audible tic tic, or thump thump coming from the fuel pump then that is your indication that the fuel pump is starving for fuel. You either have a fuel line restriction, too little fuel, a clogged filter, a clogged sump screen, or rarely, a failing fuel pump. Usually, it is a fuel line restriction.

If you hear no tic tic or thump thump and it just goes off on EE2 then the problem is in the burn chamber. You may have a carbon chain in the chamber causing the flame sensor to temporarily short out. You can clean the flame sensor, fuel nozzle, and igniter to resolve this problem until you can get your Toyo tuned up.

Dec 13, 2007 | Rinnai Toyostove Direct Vent Heater: Laser...

1 Answer

EE2 code for toyo 3


What Does EE2 Mean? Laser 30, 56, and 73 model Laser heaters cease operation and display
the EE2 code on the control panel (instead of the clock or temperature settings) when the primary
flame rod on the heater fails to sense a flame during the first 5 minutes of the Ignition and Pre-
Heat cycle. On the Laser 55 and 72 the heater will stop and the red Reset lamp will light rather
than the EE2 code. (Note: There may be other reasons for the reset lamp to come on but much of
this information will apply.)
What Can Cause An EE2 Error? The primary flame rod is the only sensor in the heater that
can cause the EE2 error. Thus, if it occurs, either there is (1) no flame to detect, or (2) the
sensor failed to detect the flame. The flame rod is located on the lower 1/3 of the burner. It is a
heavy wire with a ceramic insulator. A single white insulated wire connects this device to the
main circuit board.

Dec 12, 2007 | Rinnai Toyostove Direct Vent Heater: Laser...

Not finding what you are looking for?
Rinnai Toyostove Direct Vent Heater: Toyostove Laser 73 Shipping Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Rinnai Heating & Cooling Experts

paulcarew

Level 3 Expert

2514 Answers

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Tim Whalen

Level 3 Expert

3074 Answers

Are you a Rinnai Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...