Question about Nordic Track Nordictrack Exp 1000 Treadmill Motor Control Board 13

Open Question

My nordictrack exp1000s treadmill stops after about 30 minuits

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 84 Answers

SOURCE: my nordictrack exp1000 incline will

looks like a incline sensor

Posted on Mar 11, 2011

Ad
ercupa190
  • 12223 Answers

SOURCE: NordicTrack Treadmill A2050, Will not work at all, with key in place.

1) test the receptacle wall, plug a desklamp for to see if work if is working go
2( testing the power cord for open or defective.
3) reset the machine
4) test the fuse for blown and replace
5) test the c.breaker for tripped and reset again.
6) test the key, the key is small magnet, you can test with your magnet refrigerator with atraction or repulse, if doesnot replace the magnet from home depot.
God bless you
9_20_2012_11_40_41_am.gif

Posted on Sep 20, 2012

  • 3 Answers

SOURCE: Only certain buttons on the NordicTrack exp1000 treadmill work.

I had this same problem a few years ago. For anyone else who experiences this problem go to the Treadmill Doctor website and order a new control overlay. It fixed mine and it still runs 3 years later. It's much cheaper to buy from them than from NordicTrack, and I'm not even sure if NordicTrack will sell you just the overlay, they may only sell the whole panel which was $450 back then. All you have to do is remove the top of the control panel, unplug the old overlay, peel it off, then stick the new one on, plug it in, put the control panel back on and everything should be fine.

Posted on Oct 29, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Nordic track exp1000 stops suddenly while in use


If you wish to get some details about treadmill repair ; visit the site linked here. Pull up older posts. http://electro-medical.blogspot.com/

Jan 07, 2017 | Nordic Track Nordictrack Exp1000 Treadmill...

1 Answer

Exp1000 runs for several minutes


The control circuit has an overload and will shut down to prevent a fire. It may not be the Motor at all, just the circuit board failing.

Feb 26, 2014 | Nordic Track Nordictrack Exp 1000xi...

1 Answer

My exp1000 stops abruptly...if you are not holding on, you could topple off...help


this happen because lack of maintenance schedule.
LUBE inmediately the DECK BELT, the machine Stop, BECAUSE has a protection system for electronic component.Maybe you have a worn DECK BELT, time to change it.
2) LUBE THE rollers bearing too.
3) Measure the input voltage motor, if there are the motor need repair. see my personal TIPS.
4) measure the output voltage board, for input voltage motor, if there are NOT the board is faulty.
see the b.diagram + video and proceed
God bless you
10_13_2012_12_05_17_pm.gif

Oct 12, 2012 | Nordic Track NordicTrack Treadmill, A2550

1 Answer

Our Nordictrack Track Exp100S has problems. The belt rubs on the left hand side (my left as I'm walking) at the back of the treadmill. What should I do?


Inspect the rear plastic end cap. It is the plastic part at the back of the machine. The adjustment screws can be found there. These end caps disintegrate after time and break. You will see the discoloured plastic where the damage has occurred. If this is the case, the end cap must be replaced and belt readjusted.

Jan 04, 2011 | Treadmill Doctor Nordictrack Track...

1 Answer

Belt slipping and power supply making noise


Have you checked to make sure it is not the belt that drives the front roller from the motor slipping. Get somebody to watch while you are using the machine and determine if the motor is still spinning while the running belt has stopped.

Apr 18, 2010 | NordicTrack E4000 Treadmill

1 Answer

Our EXP1000 treadmill is about 10 years old and we have not had any problems with it. The belt recently has been going slower than before. for Example, we used to walk at a speed rate of 4.5, now it...


If belt hasn't been replaced that's your poblem. If that's more than you want to put in a 10 year old treadmill, try lubricating it. That may bandaid the problem for a while. This will progressively get worse over time.

Nov 16, 2009 | Nordic Track NordicTrack Treadmill, A2550

Not finding what you are looking for?
Nordic Track Nordictrack Exp 1000 Treadmill Motor Control Board  13 Logo

Related Topics:

260 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nordic Track Exercise & Fitness Experts

Matt Olenzek
Matt Olenzek

Level 2 Expert

297 Answers

Ross Metcalfe
Ross Metcalfe

Level 2 Expert

129 Answers

 Atlanta Fitness
Atlanta Fitness

Level 1 Expert

23 Answers

Are you a Nordic Track Exercise and Fitnes Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...