Question about LG WM-1480FHD Front Load Washer

Open Question

How to remove the front panel of a model wd1475rd lg front loader

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MNTECH
  • 1543 Answers

SOURCE: lp conversion for LG dryer

After removing the three screws which pass through the L bracket into the back of the dryer:
Stand in front of the dryer and (using the palms of your hands) give the top a sharp push back on the dryer top at the left and right side of the top. The top should slide back 1 to 2 inches. Now lift the top off.

If you post again with further questions, make sure to post under the model number you have. (you posted using a combo washer / dryer, and stated you are converting to LP, which combo units are not gas.)

Posted on Apr 18, 2009

Ad
  • 2 Answers

SOURCE: LG wash machine # wm 2277 hb front loader display flashes LE wont

We had the OE message come up and did the above procedures...that didn't fix it. I removed the dual pump modules (they come off in one piece...one is the recirculating pump, the other is the drain pump). Turns out, the drain pump impeller design sucks. Even though it turned when I put power to the pump, that doesn't mean your pump isn't bad. Once it is under load pumping water, the impeller can slip where the pin connects to it from the motor. We replaced the motor for $60 and that fixed the problem. Our unit is at least three years old and we have a family of four, so it does get used quite often. Nobody told us about the filter at the bottom of the unit and I figure if we knew this ahead of time, we probably could have avoided the impeller issue...but it is still a sub-par designed motor/impeller. The new one I ordered looks like an updated design so I don't see this happening again. It is quite easy to remove and replace the pump, btw.

Posted on Feb 21, 2010

MakeupWizard
  • 39 Answers

SOURCE: LG WD-12124RD How do I remove the front panels?

Hiya,
most machines now open from the back you will find 2 or 3 screws/bolts at the top holding on the top section if you un screw those then slide the top back slightly it should unclip allowing you to take off the top this should expose some more screws or bolts that will be holding on the front & sides, if your machine is leaking from the front you could have a leaky door seal too so you may want to check that before starting to take it apart.

Hope this helps

Posted on Apr 23, 2010

MNTECH
  • 1543 Answers

SOURCE: Does a pedestal for the

Yes, it can be used, but the fastening system for pedistal to washer is much better with the new pedistals.

Posted on Jan 25, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i drain my washer out


remove outlet hose hold end below water level empty into basen

Apr 19, 2015 | LG Washing Machines

1 Answer

How do I open to remove the water on an LG tromm front load washing machine to repair/replace the pump?


LG machines normally have a small diameter rubber pipe folded up in the drain pump basket area on the lower left side of the front panel.
Pull out the pipe and remove the small plastic end stopper to allow the water in the tub to drain.

Sep 20, 2014 | LG Washing Machines

1 Answer

Samsung sw80usp wont drain


On my LG I removed the front panel and there was a drain trap with a filter. I removed and cleaned the filter. Mine started draining again. (assuming you have a front loader not a top loader)

May 07, 2014 | Samsung Washing Machines

1 Answer

I have an LG Tromm front loader... I an getting a UE error code. I have tried all remedies I have found online...unplugged, adjusted load, adjusted size of load..Please help


First off all remove the top panel should be two screws in the rear remove these and slide the panel to the rear to remove it. Look for the tech sheet as this contains how to deal with the codes let me know

Sep 27, 2011 | LG Washing Machines

1 Answer

Wher is the pump on a front loader


It depends upon the model number, but MOST front loader washers have a drain pump located directly below the wash tub behind the lower toe panel directly below the door. To remove the panel, locate and remove the screws under the bottom front edge of the panel. With the screws removed, the panel will come off, exposing the drain pump and internal components. If you need further guidance, please post back with your MODEL NUMBER and let me know. I hope this helps you.

Nov 17, 2010 | Washing Machines

1 Answer

Front loader won't spin, just after 2 mins up into the cycle it comes up with message le. Can you help please?


Hi just read your posting.Now I need to know the make and model of your machine.It sounds like you have an LG front loader.LE on the LG front loaders means your HALL SENSOR which is attached to your motor is faulty.Please reply with model number and I am sure I can help you.Looking forward to your reply.

Sep 11, 2010 | Washing Machines

1 Answer

LG front loader washer error LE how to fix


probably a defective motor hall sensor. will require dissassembly of motor via rear panel of machine. you will need a #17 socket and breaker bar to remove rotor nut. also, you will then need a #10 socket and driver to remove motor stator. sensor will be underneath attached to stator.

Jun 26, 2010 | LG WM1812C Front Load Washer

1 Answer

Something is stuck in our LG front loader washing machine so the water wont empty in the spin cycle


There should be two screws under the front lower panel. Remove the two screws and remove the lower panel. You should be able to access the pump from here.
Inscrew the cover on the front of the pump and clean.

Dec 31, 2009 | Whirlpool Gold Duet GHW9400P 3.8 Cu. Ft....

1 Answer

How do you get front off of machine to repair part


front loader ? if if remove bottom panel to get access to screws the remove door to access the remaining screws the front should drop down on your average front loader for more info. need make and model

Jul 31, 2009 | Maytag Washing Machines

3 Answers

LG Intellowasher cannot complete spin cycle.


Unplug power cable, remove top cover and inner panel, locate water level sensor on the right with 3 wires and a thin tube, remove the tube and puff into it until you hear water bubbling. This will clear any blockage caused by suds build up. Replace tube, covers and plug back in. It should complete cycles now.

Sep 11, 2008 | Washing Machines

Not finding what you are looking for?
LG WM-1480FHD Front Load Washer Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top LG Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1467 Answers

Are you a LG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...