Question about Bulldog Remote Starter & T-Harness Kit for 95-03 Chevy Blazer/Chevy S-10 Pi

1 Answer

My 2002 Chevy S-10 security light stays on not flashing when key is on/won't start

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 652 Answers

Replace the starter switch or key switch

Posted on Apr 19, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 chevy traverse wont start after hooking amp up car was fine


OK. you had the battery disconnected. Here is what you do. Turn on the key. The security light will begin to flash. Wait (about 10 minutes) with the key in the ON position. The security light will stop flashing. TURN OFF the key. Then, turn on the key and start the car. Security system is supposed to prevent theft for a 10 minute delay. This usually discourages any thief. This will work, You just need to be patient with the 10 minutes. It seems like an hour when you wait ten minutes for that security light to stop flashing.

Mar 19, 2017 | 2009 Chevrolet Traverse

1 Answer

I can't start my 2002 chevy trailblazer after battery change. my keyless entry is damage and i fear it is the anti theft security system not allowing it to kick over, any suggestion to start?


Is the security light flashing? If it is, put the key in and turn all the way but don't start. Leave on for 10 min. Or until the security light stops flashing. Turn off and then try to start.

Apr 10, 2016 | 2002 Chevrolet TrailBlazer

1 Answer

Reset security code 2003 Chevy impaula


Instructions
    • 1 Attempt to start the car. If it does not start, or dies very quickly after it started, then leave the key in the ignition in the "ON" position and wait 10 minutes. Make sure the security light is flashing. After 10 minutes the security light will stop flashing and either turn off or stay on steadily. When it does, then turn the ignition off, wait 20 seconds and attempt to restart the car.
    • 2 Repeat this procedure three times in quick succession without removing the key from the ignition.
    • 3 Start the car following the third 10-minute waiting period. The car should start and stay on. If it stays running, then the codes have been relearned and the problem is solved. If the car still does not start then you may need to have all or part of the passlock system replaced

Jan 15, 2015 | 2003 Chevrolet Impala

11 Answers

Changed ignition switch now security light stays on and truck starts and kills


You need to relearn the passlock system (security). There are 2 ways. One is with a scanner, which most diy'er wont own an expensive one to do it this way, here is the manual way. Start the truck and let it run until it dies. The security light should then be flashing. Leave the key in the run position until the security light stops flashing (about 10-15mins). After the light stops flashing turn the key off. Try to start the truck again. It should do the same thing (run for a few seconds and then die with the security light flashing). Again wait for 10-15 mins for the light to stop flashing and then turn the key off and repeat the process one last time. That's a total of 3 times. Once you finish the process the 3rd time. Let the truck sit for a minute with the key off. It should now be programmed and start and run normally.

Jun 02, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

2002 chevy impala won't start if I jump starter


Is the security light on or flashing ?
The yellow wire goes from the key switch to the neutral safety switch, then to the starter. So bypassing the neutral safety would make the starter crank the engine, but would have nothing to do with the rest of the engine.

May 27, 2013 | Cars & Trucks

1 Answer

1999 CHEVY LUNINA WON'T START BATTERY AND


Check the dash once you turn the key to the run position the passlock runs a security check using a set resistance value through the chip in the key. If the security light begins to flash the reading it received was incorrect or it didn't get a reading at all. You can try reseting the value it is looking for by turning the key to start then releasing it. After 10 minutes turn it off then cycle it start again leaving it in on for 10 minutes then back to off then one more time. After the third cycle has completed for a total of 30 minutes. You should be able to turn the key on and start the vehicle. If the light continues to flash their is a problem with the chip in the key or the connections within the ignition its self. Both are common but a Pass Lock Relearn as described above will usually adapt to the poor connection values. Hope this helps.

Aug 28, 2011 | 1999 Chevrolet Lumina

1 Answer

I have a 2002 chevy silverado 1500 it seem that it is not getting fule it will not stay running and will start for a second but then stop when I try to give it gas or not give it gas I think it is the fule...


sounds like the security system is malfunctioning. When you turn the key on does the security light stay on steady or flash? If flashing leave the key on for about fifteen minutes till it stays on steady. the engine should then start. if it does not go steady, likely you need to replace the ignition key switch assembly.

Sep 10, 2009 | Chevrolet 1500 Cars & Trucks

2 Answers

My 2002 Grand am is have a passlock problem. The


I discovered the hard way- ($85.00 later) Step 1: turn key to "on" position. step 2: open driver door. (security light should be flashing on and off) step 3: wait ten minutes with key in "on position and driver door open. step 4: when 10 minutes is up-(youll know-because security light will have stoped flashing after 10 minutes) close driver door ,turn key to "off" position, then turn key "on" to start. drives me crazy!! I have to do it to mine sometimes 2-5 times a day! GM doesnt have a fuel reset button etc. like fords do.

Jul 17, 2009 | 2002 Pontiac Grand Am

1 Answer

Prblem car won't start


Turn the key to on. The security ight should be flashing at this point. The key should be turned to on for about 10 mins. The security light will be steady now, the turn off then start it. This re-sets.

Jun 02, 2009 | 2002 Pontiac Grand Am

Not finding what you are looking for?
Bulldog Remote Starter & T-Harness Kit for 95-03 Chevy Blazer/Chevy S-10 Pi Logo

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bulldog Security Vehicle Parts & Accessories Experts

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

John
John

Level 2 Expert

509 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Bulldog Security Vehicle Part and Accessory Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...