Question about Brother DCP Office Equipment & Supplies

Open Question

Brother mfc diagnostic code 22 - DCP Brother Office Equipment & Supplies

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am getting diagnostic code 22


Error Code: 22
Description: Engine Coolant Temperature circuit malfunction.
Possible Causes:
- Wiring.
- Coolant Temperature sensor defective.
- ECM.

Apr 25, 2014 | 1993 Jeep Grand Cherokee

1 Answer

I have a Brother MFC-7440N machine. On 7/22/10


The toner cartridges have a small port on the side that the printer uses to check the toner level. Our 7440N tells us it will soon need a new toner cartridge and will then print another 400 copies. Search YouTube for Brother Toner Cartridge and it will show you how to modify the cartridge by covering up the portholes with tape. Since there is obviously some kind of sensor, you might need to get a can of air and clean out any extra toner. Lastly, the Brother cartridges have "reset gears" which are replaced when the cartridges are refilled. You might have a cartridge which the gears were not replaced on.

Jul 26, 2010 | Brother MFC-7440N Laser Printer

1 Answer

MFC8500 VERY DARK STREAK (.25 INCH WIDE) RUNNING DOWN THE ENTIRE WIDTH IOF THE PAGE.


Reference page 22-17 in reguards to cleaning the charge wire on the drum unit and page 22-16 for cleaning the document scanner. This is a link to your Brother MFC 8500. Hope this helps.
http://www.brother-usa.com/ModelDocuments/Consumer/Users%20Manual/UM_MFC_8500_EN_1354.PDF
If the dark streak appears on printed documents, cleaning the charge wire will correct it.

Nov 04, 2009 | Brother MFC 8500 All-In-One Laser Printer

1 Answer

After 4 rings our fax machine picks up automatically,


Your owner's manual will tell you how to program the MFC. There is one on the install disk, too. If necessary, you can get one by Googling your machine.

Mar 28, 2009 | Brother MFC 7420 All-In-One Laser Printer

1 Answer

Brother mfc-410cn colour cartridge problem


There may be three problems here.

1.Not doubting your skills for one minute, nor wishing to offend you in any way, but did you remove the protection strip off of the Magenta ink cartridge? Sometimes we forget to do that.

2.Once a new ink catridge is installed, it's best to go to the Brother diagnostic tools section, and run a test. Sometimes an error code is kept, (Ink cartridge is empty), and the diagnostic tool checks this out. It then clears the error code, and 'recognizes' the new ink cartridge.

3.Ink may have dried, for the tiny little holes for the magenta ink cartridge, where it attaches to the body of the printer. Just this one ink cartridge. Suggest you don a pair of rubber dishwashing gloves. MFC-410cn -> Unplugged <- from the surge protector, use a clean, lint free, warm water, damp cloth, and wipe the holes for the ink cartridge, where it lines up with the printer body. This will be where you see that copper metal strip. (Or perhaps it's brass)

To clarify, you are cleaning the printer body. The area where the ink cartridge goes, and the metal strip. The ink passes from the ink cartridge, and goes through holes in the body of the printer. The metal strip is where these holes are located. Allow this area to dry. You may want to use a hair dryer set on low heat to speed the drying process up. Constantly move the hair dryer back and forth. Keep it about a finger length away.

Once you are satisfied this are is dry, reinsert the magenta ink cartridge. Plug the printer back into power. Advise waiting one minute, then turn the printer on.
Use the Brother diagnostic tool.

Should you not be able to find the Brother diagnostic tool, I suggest you go to Start>Hover your mouse cursor on All Programs>Go over to Brother>MFC-410cn>and to the Help section. The Help section, will tell you how to open the diagnostic tool.

Aug 19, 2008 | Brother MFC-410CN All-In-One InkJet...

1 Answer

Installation diagnostics


Hi press start the search type in the required fie name press enter then once it appears double click and it will open. Or you could right hand click copy and paste it back or on desktop

Thanks J

Feb 02, 2008 | Brother MFC 7420 All-In-One Laser Printer

3 Answers

Self diagnostic will complete automatically in 10 minutes


Problem for Brother MFC-7420 All-In-One Laser Printer Self diagnostic will complete automatically in 10 minutes

Aug 01, 2007 | Brother MFC 7420 All-In-One Laser Printer

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Brother Office Equipment & Supplies Experts

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Ron Dufek
Ron Dufek

Level 3 Expert

398 Answers

James Cagle
James Cagle

Level 2 Expert

453 Answers

Are you a Brother Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...