Question about Wareforce CG Underbar Glass Washer 208/230V

1 Answer

How to adjust hot water Gets too hot - Wareforce CG Underbar Glass Washer 208/230V

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,957 Answers

Check you data plate. The inlet temperature must match the machine requirements, which means that your incoming water is too hot and the water heater temperature needs to be turned down. Here is a link to a installation/service manual. http://www.webstaurantstore.com/documents/pdf/wareforce_cg_service_manual.pdf

Posted on Mar 23, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can i replace thermostat on power vent hot water heater, water only gets to 105 degrees


are you sure that it is non adjustable .some people do not want scalded with hot hot water

Feb 17, 2015 | Water Water Heaters

1 Answer

Hi i have installed a few bosch gas geysers at our lodge in mozambique.The problem is that the water gets hot when we turn the water on then the heat just shuts off and the water gets cold after a short...


The problem with all that type of water heater is that once the hot tap is turned on sufficient flow must be maintained through the water heater to keep the main gas burner alight. If the heat adjuster is turned up to high, then the person using the hot water will turn it down to a low rate which means the main burner will turn off and result in cold water. Try setting the heat control to the lowest setting that still gives hot enough water. If you have a thermometer adjust control for a temperature of around 50 to 55 degrees Celcius. You may have to fiddle with fine adjustments to get the temperature and flow rates to maintain a constant output of hot water. You may still have intermittent problems. If the heater only supplies baths or showers you could set the temperatuer even lower (45 to 50) to ensure that the hot tap is used more than the cold which will maintain flow and therefore heat.

Nov 22, 2010 | Bosch AquaStar Indoor Natural Gas Tankless...

1 Answer

Water gets to hot and hot water spits air in line ? no water leaks


If it is DSI ignition, there is thermostat and ECO behind that little foam pad with letters on it "Therm", and "ECO", that may need to be adjusted, or replaced. As far as adjustment goes, you want to make sure disc is making good contact with tank surface.I must ask though, are you using city water hook-up, or on board pump to pressure system? As well, have you tried draining water heater and re-filling just to see if that helps?

Nov 12, 2010 | RTO Atwood DSI-RV Water Heater-6 Gallon

1 Answer

Hot water gets too hot trips off at tank then water gets cool and i push reset button and water gets hot again real hot thentrips off again


It's time to replace your thermostat. Instead of maintaing the correct water temperature, the water is getting so hot it is acivating the safety circuit breaker. If this breaker were to fail, you could have a devastating explosion

Mar 21, 2010 | RELIANCE ELECTRIC WATER HEATER

1 Answer

Pilot light went out but will can,t get it relit it only stays on as long as I hold the button down


Is the thermocouple in the pilot flame? & does it get hot [glow red] If not adjust position until it does & make sure it's clean
If thermocouple gets hot but no relight, replace couple

Oct 26, 2009 | Bosch AquaStar 125FXKIT-NG 125FX Natural...

Not finding what you are looking for?
Wareforce CG Underbar Glass Washer 208/230V Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Wareforce Water Heaters Experts

Donni Steen

Level 3 Expert

659 Answers

Brad Brown

Level 3 Expert

15478 Answers

Gil Shultz

Level 3 Expert

3368 Answers

Are you a Wareforce Water Heater Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...