Question about Telex Radio Communications

Open Question

Have A telex pas-1 wireless mic that omeone else worked on. need shematic with part numbes to repair.

Someone else repaired with jumper wires and non soldered parts. don't know what part numbers should be used.

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: My mic is broken

What i've done in similar situations is basically trail and error. You've got two spots for one wire, try them both out.

Some companies will use a generic piece for all their similar products. Maybe one of Altec's other headsets uses that 5th spot for something. Just try them both out and see what happens. Just dont solder them right away, stick them on with some electrical tape or something to save yourself some time. Then when you're sure you can solder away.

Posted on Jan 07, 2008

SOURCE: need help for hs-23 headset repair

In this middle section, the wires are as follows: MIC+: Yellow MIC-: Black L+: Blue L-: Copper/Grey Stripe? R+: Copper R-: Copper/Grey Stripe? (same as L-, they should be interchangeable...) Sirial?: Yellow/Orange Stripe Uout: Red GND: Green Hope this helps!

Posted on Jun 08, 2008

  • 1833 Answers

SOURCE: echelen/telex headset [no model #

Hi,

For repair you can send it any good repairing.

Or you can contact with company customer service.

Posted on Jan 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I order a mic clip for the wireless mic. The one I have broke.


Contact Bosch/EV (formerly Telex) via website or call them. They're in Burnsville Minnesota and their customer service is excellent.

Feb 25, 2011 | Telex WT-55 Belt Pack Transmitter (027)...

1 Answer

I have a telex turner 56 handheld mic. the cord was snagged and pulled all of the wires off of the ptt switch. I need a diagram or some assistance i am using this on my connex


if it pulled them off the switch you may need a new cord ?? or just get a new on they only $38.99.. well thats what we selll them for... most replacement mic cables are $14.. they someone installing.. $5... theres $20 easy.. pin 1 ground
pin 2 audio, pin 3 tx, pin 4 rx..

Feb 15, 2011 | Connex Radio Communications

1 Answer

We are using a Shure PG58 wireless mic. It worked very well for about 1 year and then it would work on/off. Even when we put new batteries in the mic it still just goes dead. Any suggestions?


Unfortunately, there are many, many things that can cause a unit to be non-functional. Try calling Shure to get it repaired, or call Delta Audio at 773-764-3634. Delta Audio also repairs older Shure equipment.

Jan 17, 2011 | Shure UT2 / 58 / PG58 Professional...

1 Answer

Voice coil open circuit - replace?


The diaphramgm price is $224.00 to do it yourself with no warranty. If you send it in to be repaired it's $200.00 with warranty. Telex Communications handles all Electro-Voice repairs In Lincoln, Nebraska @ 1 800 553 5992 ask for RE-20 diaphragm repair info.

May 04, 2009 | ElectroVoice RE20 Professional Microphone

3 Answers

Electrovoice RE20 will not work with my board...


If you've tried a different cable and it still doesn't work it probably the capsule.The capsule is available for $224.00 .If you send it in for repair it's only $200.00 and they give you a warranty.Contact Telex Communications @ 1 800 553 5992 and talk to a represenative and they will give you the info you need to send it in for repair.

Feb 28, 2009 | ElectroVoice RE20 Professional Microphone

1 Answer

Telex WT55 wireless lapel mic & FRM70 Receiver


How do I set the squelch on a TELEX FMR-70 receiver?

Jan 27, 2009 | Telex FMR70 VHF Wireless Microphone...

1 Answer

Telex ProStar VR12 VHF needs repair


I've been in contact with Telex and although the Prostar is obsolete they still maintain some repair parts. I would contact them:

http://www.telex.com/Support/

Jan 07, 2009 | Telex FMR-200H Professional Microphone

1 Answer

Telex prostar wireless mic.  leads came off of mic element.  One green wire and one black.  Which one connects to center of element and which connects to rim.


Hi..
The rim is "ground" or the (-) side of the mic.
Find out which wire goes to ground or a (-) on a battery.
Solder that one back to the rim

Dec 11, 2008 | Telex FMR-200H Professional Microphone

6 Answers

Mic wiring diagram


Same as Omega
#1 Mic Audio
#2 Receive
#3 Transmit
#4 Up/Down for channels
#5 Ground/Shield
#6 13 volt

Jan 13, 2008 | Magnum DeltaForce CB Radio

Not finding what you are looking for?
Radio Communications Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Telex Radio Communications Experts

The Knight
The Knight

Level 3 Expert

74106 Answers

Mike Charette

Level 3 Expert

1795 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

14804 Answers

Are you a Telex Radio Communication Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...