Question about Frigidaire FGB24S5A Gas Single Oven

Open Question

LGGF3044LB SMOKE FROM THE CONTROL PANNEL

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F7 indication on the oven Pannel


F7 A = Function pad button stuck or
B = Bad clock Unstick button or
Replace Electronic Range Control (ERC)

Jun 12, 2011 | GE Ovens

1 Answer

Hello, I have a Turbochef tornado oven, while operation i am getting a Fault code Close door and keeps on coming while closing the door with a beep . Can you please try to resolve the error and solve. Your...


This option is only for the people whose primary switch is okay.(Anyone who know how to use multimeter can reply me for solution dealing with electrical system
There are two things you have to do.
1. Door alignment.
Sometimes the door gets mis aligned due to excessive use of oven......because people smack the oven door alot.
FOR ALIGNMENT
MAKE SURE YOU TURN OFF OVEN AND DISCHARGED CAPACITORS.(IF YOU DON'T KNOW HOW TO DISCHARGE THEN REMOVE THE OVEN PLUG AND WAIT FOR 1 HRS TO DESCHARGE CAPACITORS
1. Remove right side pannel
2. remove all the wires and cables that are connected to controle board which are comming from the controle pannel(the pannel that has display and buttons ).
3. There are two nut (9mm or 10mm) that you have to remove to take apart the front control pannel.
4. Once you remove the pannel, put it aside.
5. Now take out all 4 black caps from the oven door.
6. Ready for alignment
7. Lose all four bolts just give 2 turns to lose(don't lose too much).
8. Tap door at the center and then hold it with one end.Use other hand to tighten the bolts.
Now your door is aligned.
Reinstallation is reverse of removal.
SECOND THING
1. open the left side pannel
2. At the top where the door latches .There is an primary switch which needs to be adjusted.
3. loosen the switch and then retighten by aligning it in correct way.

Thanks
SAGAR

May 12, 2011 | TurboChef TORNADO Electric Oven

1 Answer

Control Panel Light is out.


I'm not sure if you have removed the trim on the right and left front. so if you have not then open the bottom oven door and in the lower right and left corner near the hing should be a screw, remove them and pull down on the trim pice and now this will revial a screw at the top right of the control pannel on the left and right , now remove them screws and make sure power is turned off at the fuse box and lift on the control pannel. if this does not work you will need to remove the unit.

May 24, 2010 | Whirlpool RBD305PR Electric Double Oven

1 Answer

Model RBD245PDB14 Error code F2 E6(left side) replaced original key pad with new. One week after install same error code and display blank out. Unpluged and reattached key pad cable but still diplays F2 E6...


If you replace the keypad and continue to have the same error you also have to replace the electronic control.

You can contact fixyourboard. com for a price to repair your control at a reduced price over a new control. It also comes back with a better warranty than anew control.

Jan 03, 2010 | Whirlpool Ovens

1 Answer

Whirlpool double oven Model#: RDB305PDB12 Ran self cleaning oven and it completed the cycle and unlocked. Lost power - checked breakers and they are ok. The oven now has no power to it. Any ideas? Thanks,...


there is a tco (thermal cut off) part under the control pannel.
the local electronics store had them but not the right temp. choices for me where 1 degree cooler or 7 degrees hotter. the part was under $4. online for the right temp they wanted $15.75 s/h. In my oven it was inline with a black wire. both ends had the knife quick connects and is covered in a thick clear plastic. Be carefull. I dont know how but the ribbon cable for the control pannel broke while i was working on it. :( this $4 part did bring the power back on but because of the cable issue no keys worked.

Oct 07, 2009 | Whirlpool Ovens

1 Answer

ERROR F6


HI, the reason for the non responsive control is being caused by a major fault within the control circuits. the entire control board will need to be replaced. it has failed at this point.

Replacing the Oven control board will solve this issue.

Jul 19, 2009 | Ovens

1 Answer

LED display says door. The control pannel wont work at all.


My problem has been repaired by my husband. I do not have the self cleaning on my oven yet the control board thought my self cleaning was on and the door was open. He had to jumper a wire between a connection on pannel to confuse the code and cause the board to set a new error code that could be reset. Which we were able to set the EO code and follow procedure for power disconnect and the board rest. We now have an opperatioal oven. Thank you .

Nov 23, 2008 | Whirlpool SB160PEE Gas Single Oven

1 Answer

After self clean ge electric oven want heat


the oven sensor located between the brolier element, its connector melted. replaced for 10.00
works fine

Nov 13, 2008 | Ovens

Not finding what you are looking for?
Frigidaire FGB24S5A Gas Single Oven Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Frigidaire Ovens Experts

Dan Webster
Dan Webster

Level 3 Expert

8220 Answers

 Fix Your Board
Fix Your Board

Level 3 Expert

310 Answers

ashburton

Level 3 Expert

417 Answers

Are you a Frigidaire Oven Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...