Question about Bushnell Tour V2 Pinseeker Laser Rangefinder

Open Question

Moisture on inside - Bushnell Tour V2 Pinseeker Laser Rangefinder

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove moisture inside Olympus digital camera


Place it in a sealed container covered in rice for a few days. The rice will absorb the moisture. Works on cell phone dropped on water too.

Sep 02, 2014 | Olympus TOUGH TG-310 Digital Camera

1 Answer

Moisture Inside Watch Face


take the back off and place it on inside of the house windowsill, this hot, sunny dry environment will speed the drying process, it may take a few days.

Apr 29, 2014 | Garmin Forerunner 610: Sport Watches

1 Answer

Passenger side headlight has visible moisture in it. what could the problem be?


The reson why there is a moisture inside your headlight is because the rubber that seals your headlight bulb at the back of your headlight is already worn out, so the heat coming from your engine will add to it causing the moisture to built in inside your headlights. In addition, the cold temperature outside the headlights will create a moisture inside your headlights.

Jul 05, 2011 | Ford Taurus Cars & Trucks

1 Answer

I have moisture inside my headlight on my 2007 gmc denali. will i have to replace the entire assembly. The lamp is out, could that cause the moisture. Or does the moisture cause the lamp to burn out.


{: ) Some exterior lamps, such as cornering, turn signal, backup, headlamps or tail lamps may exhibit very small droplets of water, a fine mist or white fog (condensation) on the inside of the lamp lens. This may be more noticeable on lamps with "multi-lens" designs and may be normal during certain weather conditions. Condensation occurs when the air inside the lamp assembly, through atmospheric changes, reaches the "dew point". When this takes place, the moisture in the air within the lamp assembly condenses, creating a fine mist or white fog on the inside surface of the lamp lens.
Most exterior lamps on General Motors vehicles use a vented design and feature a replaceable bulb assembly. They are designed to remove any accumulated moisture vapor by expelling it through a vent system. The vent system operates at all times, however, it is most effective when the lamps are ON or when the vehicle is in motion. Depending on the size, shape and location of the lamp on the vehicle, and the atmospheric conditions occurring, the amount of time required to clear the lamp may vary from 2 to 6 hours.
Completely sealed headlamp assemblies (sealed beams) are still used on a limited number of models being manufactured today. These lamps require the replacement of the complete lamp assembly if a bulb filament burns out.

If moisture or droplets appear after being exposed to rain or washing, you can try putting some weather seals on the edges where you think the seal is poor. Check also the headlamp caps. In any case, if the moisture doesn't clear no matter what drying approaches, better replace the assembly.
The bulbs won't cause the moisture, but it is possible that an accumulated moisture on the bulb itself can disable it, although rare.

Jun 27, 2011 | 2007 GMC Yukon Denali

2 Answers

What would make my windshield frost up from the inside--I park in the garage at night and during the day while I'm at work the windshield frosts up from the inside so I have to scrape it


Moisture inside the vehicle. If you have a water leak that is allowing water to get into the car it will cause this problem. Also if the A/C water drain is plugged and there is water standing in the blower fan area you will have the same problem.
Pull your carpet back on the driver and passenger side at the fire wall and check for moisture, if the carpet backing is dry on both sides you will want to check the drain under the hood.
Good luck.

Nov 15, 2009 | 1998 Oldsmobile Intrigue

1 Answer

Moisture on the lens


If moisture is in the lens, it is inside the camera.
Best to remove the battery or batteries and let it dry out in a warm area for a few days. This may not remove the moisture like taking the camera case off. This may be a job you may not want to tackle.
Corrosion will eventually cause problems within the camera.
It may be that the moisture inside may already have damaged some parts or components or caused a short.

Oct 04, 2009 | Olympus ? 850 SW Digital Camera

1 Answer

1999 ford taurus with moisture in the headlights


Most headlights lens are sealed up to prevent this problem. A broken seal or a crack somewhere opened up to let in moisture.
You can drill a small hole on the lowest part of the plastic headlight housing to let the water drain out. Or, replace the plastic headlight assembly with a new sealed one.The plastic headlights turn yellow and cloud up over time (not because of moisture inside, because it's plastic getting ruined by the weather and the sun). This problem reduces headlights from putting more light on the road.
The only thing you can do with moisture inside the headlights is to drain out the water that builds up. The seals on the headlights are bad right now and are going to keep letting moisture in. I would replace the both headlight assemblies for new sealed, clear ones.

Sep 23, 2009 | 1994 Ford Taurus

1 Answer

4Runner headlight has moisture inside. Light works fine


yes. it should be a fairly easy job, just be careful when removing the glass, and make sure you get your headlight re-alligned when it is done, as it will fail its mot if not done.

hope that helps.

Mar 18, 2009 | 1999 Toyota 4Runner

1 Answer

My iPod has moisture inside. It turns on but


Not sure if this will help, however when a cell phone gets moisture in it, you stick it in rice and the rice will draw the moisture out. Leave it in the rice for 24 hours and see if this helps. It's worth a shot. Good luck!

Mar 10, 2009 | Apple iPod nano

1 Answer

How can I avoid camera moisture condensation on my Sony a1e camera, it keeps saying turn off for one hour or eject tape and is doing this constantly.


Camera gives Moisture error sign if it really have moisture condensation inside or its moisture sensor itself got defective.

if moisture is inside, blow hot air in camera mechanism for 5-6 minutes by hair dryer (not so closed with mechanism) and check / test.

If problem still exist it means moisture sensor is defective and i know its Sony high-end model camera and know how to fix it yet I would recommend to take camera to Sony Service center for proper repair.

Dec 06, 2008 | Sony HVR-A1E HDV Digital Camcorder

Not finding what you are looking for?
Bushnell Tour V2 Pinseeker Laser Rangefinder Logo

Related Topics:

80 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bushnell Optics Experts

Joe Lalumia aka...
Joe Lalumia aka...

Level 3 Expert

3186 Answers

kakima

Level 3 Expert

102366 Answers

Mark Campeau

Level 1 Expert

44 Answers

Are you a Bushnell Optic Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...