Door lock how do I remove lock on to replace. is there a video to help ty

Yellow flashing light? Did you get any picture? Bet, not!
It means: your lamp door interlock is not engaged: did you forget to turn the locking knob? Did you install lamp compartment door? That might be the only issue. Lamp timer blinks 'red", while TV works normally. Reset the timer, it's gone, along with annoying message. Yellow means: interlock or thermal protection is off. Try to repeat lamp installation procedure. then, you'll find out your mistake. don't need to remove the lamp. It would be "red", if lamp won't fire up.
good luck,
Alex.

Hi

This is quite simple you take your door seal off the front portion of your panel take two screws off holding the door switch , i beleive the tool you need is a torx20. Once you have it unplug quick connect wires and reverse procedure for installation.

TY
Luigi

Remove the panel beneath the door (2 or 3 screws). Reach up, there is a little "ring" beneath the door lock. Pull this down, it releases the mechanism most likely u will should replace the door lock so this doesnt happend again here are two links one so that u maybe able to get your part number and another showing an expanded view of what you will be looking at
http://www.searspartsdirect.com/partsdirect/part-model/Whirlpool-Parts/Washer-Parts/Model-GHW9150PW4/1198/0153200/W0607226/00002?blt=06&prst=&shdMod= http://www.searspartsdirect.com/partsdirect/partsdirect/showSubComp.pd?imageUrl=http%3a%2f%2fc.searspartsdirect.com%2flis_png%2fPLDM%2fW0607226-00002.png here is also a video showing how to replace a typical door lock as well i looked at the video for the duet its not as good as this one http://www.youtube.com/watch?v=noB2W06hcUs&NR=1 if you have any further questions please message me back and please remember to rank how this opinion has helped with your appliance situation Thanks again Rick p.s note this video is of an aeg which is differnt to get into then the whirlpool but the location of the door lock and how to remove is along the same principle

the 608h series unit have a variable speed pulley assy. and some have also a an ty vibration assay. fri st remove the deck belt from motor, take out the bolt engine pulley drop down remove belt, on the verbal loosen the bolt left the upper belt off and now left the center pulley up and remove the engine belt. should have the brake in lock posh ion fri st sorry. know if you have an an ty vibration pulley remove the spring and unbolt the pulley . feed the belt throw reassemble. hint have the deck in the full up posh ion for better removal. good luck

hello,good day,try to open the siding,maybe some door mechanism is worn out or disconnected to door lock mechanism,ty

hello,good day,seems your have a bad contact on driver and passenger switch door actuator,maybe loose contact or mechanical defect,which not sending a signal to your central locking pump,try to remove your rear seat,look your pump,right side,driving direction,lock and unlock your car,observe your pump is working,if not,check or replaces your switch door actuator,ty

hello,seems you have a sticky siding maybe because of plastic clips,try to insert a plastic wedge siding and door,pull the lower part and lift a bit,observe the movement of siding,how about the screw in lower armrest,press off the cover,then look for screw,be sure no screw are fitted,ty

Possiblities:

Door Lock Mechanism broken.
Check Door Lock/Switch Assembly for foreign objects
Check Wire Harness connections to the Door Lock/Switch Assembly and Central Control Unit (CCU)
Door Lock/Switch Assembly Failure

To open, remove the lower panel (3 Torx screws), reach up and pull the ring on the bottom of the lock.

hi,remove black plastic cover near the handle,then you can see one screw,remove,door lock plastic cover,remove,cover for side mirror cover remove ,then lift the whole panelling,ty