Question about Kyocera FS-4000DN Laser Printer

1 Answer

Paper cassette not being detected as full

I install paper into the cassette and select the correct paper size but when the tray raises, the printer does not detect that it is in the up position and just keeps trying to raise the paper which causes the gears to click trying to raise the paper more even though it's already up. Help??

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 78 Answers

There is a limit switch that detects when the paper is up.Check it to see if it moves freely.

Posted on Apr 26, 2014

Testimonial: "The limit switched had a bent bracket preventing the roller assembly to raise up and set into the sensor..However, now that it does sense the paper, it detects a jam when the tray is empty. It does not sense paper out....What could be causing that problem??"

  • jcoch8
    jcoch8 Apr 29, 2014

    the paper out sensor is not working correctly.check to see that the flag is going between the sensor,

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

leroyal
  • 2120 Answers

SOURCE: kyocera fs-3900DN

Very weird message! Pull down the by-pass tray in the front of the printer and insert a sheet of paper , then print.

Posted on Jan 23, 2009

copiersplusw
  • 136 Answers

SOURCE: Paper Jam

Ok, The Copystar CS-1820 is a Lemon, as an Authorized Independant dealer for Copystar. I can attest to this. This is a common problem from Copystar and their's not much that can be done. Unfornatel they should of stuck to the CS-1810 design they would of been better off/

Posted on Mar 10, 2009

  • 25 Answers

SOURCE: paper tray full message and not printing

there is a black tab in the center where the papers come out that is the tray full sensor arm that is more then likely stuck

Posted on Jan 07, 2009

  • 7 Answers

SOURCE: wont print on card stock, legal paper- keeps jamming

Menu> scroll to Paperhandling> MP Tray type>>(plain) try changing this to cardstock  <enter>
instead of MP Tray type do the same for Cassette if you desire....
Best, danakadan

Posted on May 30, 2009

  • 167 Answers

SOURCE: Copier says there is no paper in tray when there

Check what size paper you are telling the machine to print on to as the nachine does not have the correct size paper in it will come up with this message constantly.

Posted on Jun 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What corrective action for a 'no paper, add paper' message?


Hello,


Please take out the paper cassette tray and see if there is a paper sensor hanging down underneath the machine. Also check to see if the paper cassette tray is lifting up. The tray should make a noise when lifting up. Check to see that the printer recognizes the correct paper size.

Jul 09, 2015 | Dell 2155cdn All-In-One Laser Printer

1 Answer

Red light flashes, screen says "load correct paper: A4." The paper is alreay loaded. I cannot print.


When <LOAD CORRECT PAPER> appears on the display, the size of the paper in the paper cassette or multipurpose tray is different from that of the paper specified in <PAPER SIZE> for <CASSETTE> or <MP TRAY>. You need to load the correct size paper or change the paper size in <PAPER SIZE> for <CASSETTE> or <MP TRAY>.
Check if the size of paper loaded in the paper cassette or multi-purpose tray meets the paper setting specified in the machine.

check the following:
1. The paper size specified on the printer driver screen
2. Paper loaded in the machine
3. The paper size set in <PAPER SIZE> for <CASSETTE> or <MP TRAY>

If you need any technical help on printer then you can reach at http://www.vtechsquad.com/

Jan 16, 2013 | Canon ImageCLASS D1120 All-In-One Laser...

1 Answer

How do I have printer switch from empty paper tray 1 to the full 550 paper tray 2


Hi. You need to do tray linking. When one linked tray is empty, paper feeds from the next linked tray. The size and type settings for all trays must be set from the Paper Menu. To set the paper type or size:
1. On the home screen, touch Menu button
2. Touch Paper Menu
3. Touch Paper Size/Type.
Note: To link the multipurpose feeder, Configure MP must be set to Cassette in order for MP Feeder Size or MP
Feeder Type to appear as a menu item.
4. Touch the right or left arrows to select the same size paper from all paper sources to be linked.
5. Touch the right or left arrows to select the same type paper from all paper sources to be linked.
Note: When the Size and Type settings are the same for any trays, the trays are automatically linked.
6. Touch Submit.
Submitting changes appears.
7. Touch Home to return to the home screen.
Hope this helps.

Mar 16, 2010 | Lexmark X464DE Mono Laser MFP, 38ppm A4...

1 Answer

I cant find my manual how to i place the paper underneath so it feeds through the bottom


You can use the paper cassette located at the bottom of the printer, on the front when the output paper tray is closed concealing the paper feed switch, the usb port and the cassette lamp.
1 Gently pull out the cassette from the printer.
2. Remove the cover from the cassette.
3. Place your paper in the cassette tray.
a. when using A5 or larger sized paper (non standard sized paper, pinch the tab and extend the cassette if needed.
b. legal sized paper is not loadable in the cassette
4. Do not load paper above the load limit mar4k.
5. Make sure the print side of the paper is facing down.
6. Align the paper stack against the right side of the cassette
7. Slide the paper guides so they fit the loaded paper stack.
8. The paper cassette will hold up to 150 sheets of plain paper, however you do not eant to stack any more than 50 sheets in the Paper Output Tray.
9. Reinsert the cassette into the printer. Then set the cover on the cassette. Now make sure the cassette is pushed al the way into the printer. (If long paper was used and the cassette was extended iy will now extend beyond the front of the printer
10. Prepare the paper output tray by opening the front cover and pulling out the tray extension until extended completely.
11. Press the paper feed switch so the cassette lamp lights.

You can slo select the paper source with the printer driver if you prefer .

Mar 07, 2010 | Canon Office Equipment & Supplies

1 Answer

Im having canon ir400 copier.in first cassete im using A4 size paper.it was wrking fine.Suddenly m/c doesnt detecting the first tray.ITS SHOWING '' LOAD PAPER''.even i've loaded a paper...


First I would pull the paper tray out and look for a wade of paper jamed behind the paper tray or jamed in the paper path above the cassette. Another problem could be that the tray is not lifting. If you take the second tray out and reinstall the first tray can you look under the tray and see it raise up or does it make a noise and not lift. It could be the rachet gear is broken that lifts the paper up. These are just a few ideas.. Good Luck

Oct 10, 2009 | Office Equipment & Supplies

1 Answer

Suddenly my printer stopped printing - online and ready light will not come on - printer displays a flashing ''pc install'' how do i fix this problem? help!


From Service manual >
The printer currently has the Lower Cassette or duplexer
selected as the paper source, and has detected that the
Paper Cassette (Tray 2), which serves as a paper guide for
the Lower Cassette, is not installed. Install (reseat) the
Paper Cassette.

Apr 06, 2009 | HP LaserJet 4 plus Printer

1 Answer

Message keeps paper tray is full and it is full.


pull cassette out and look inside the cassette bay on the left side. there is a white gear that lifts up your paper. that might have come unseated. make sure its seated in right by pushing it back in. last but not least, make sure you don't have your rear paper stopper in cassette pushing paper too hard against the front of cassette preventing paper from raising up.

Mar 09, 2009 | Brother MFC-8460N All-In-One Printer

1 Answer

Dell 3100 CN printer...message on printer reads load tray


Cycle Power on the Printer
  1. Turn the printer off.
  2. Wait 10 seconds.
  3. Turn the printer on.
  4. Determine if the issue still occurs.
Verify There is Paper in the Tray

Verify the Paper Size
Look at the chart below to verify that the paper size meets the 3000cn / 3010cn / 3100cn-series specifications.
941802c.gif

Verify the paper size in the tray matches the size set in the 3000cn / 3010cn / 3100cn-series printer´s operator panel.

To verify the paper size in the tray matches the size set in the printer's operator panel, perform the following steps:
  1. Press the MENU button.
  2. Press the down arrow until Tray Settings appears and press the return%20arrow%203100cn.jpg button.
  3. Press the down arrow until Paper Size appears and press the return%20arrow%203100cn.jpg button.
  4. Press the down arrow until the specific paper tray (Tray 1, Tray 2, or MPF) appears and press the return%20arrow%203100cn.jpg button.
  5. Press the down arrow to select the specific paper size, as shown in Figure 1, and press the return%20arrow%203100cn.jpg button.
  6. Press the MENU button.
43d7cbe.gif

*1 Denotes country-specific factory default values.
*2 Available for the optional 250-sheet cassette only.

Figure 1 - Paper Size Chart





Verify the Paper Type Matches the Type Set in the Printer´s Operator Panel

To verify the paper type matches the type set in the printer's operator panel, perform the following steps:
  1. Press the MENU button.

  2. Press the down arrow until Tray Settings appears and press the return%20arrow%203100cn.jpg button.

  3. Press the down arrow until Paper Type appears and press the return%20arrow%203100cn.jpg button.

  4. Press the down arrow until the specific paper tray (Tray 1, Tray 2, or Multipurpose Feeder) appears and press the return%20arrow%203100cn.jpg button.

  5. Press the down arrow to select the specific paper type, as shown in Table 1, and press the return%20arrow%203100cn.jpg button.

  6. Press the MENU button.
91a7233.jpg
Table 1: Paper Type Chart

All media types that are not Plain 1 should be printed from the MPF only.


Verify the printing preferences on the Dell™ 3000cn / 3010cn / 3100cn / 5100cn-series printer.
To verify the printing preferences is set to print from the correct tray with the correct paper size, perform the following steps:
  1. Click the Start button, go to Settings, and click Printers and Faxes.
    The Printers and Faxes window appears.
  2. Right-click Dell Laser Printer 3000cn / 3010cn / 3100cn / 5100cn-series and click Printing Preferences.
    The Printing Preferences window appears.
  3. Verify the Paper Size drop-down is set to the correct paper size loaded in the specific tray to be printed from..
  4. Click the Paper Tray tab.
  5. Click the Paper Source drop-down menu and select the specific tray to be printed from.
    This sets the size and tray defaults.

Verify the Paper Size From the Printing Application Matches the Designated Printer Tray
To verify the paper size from the printing application matches the designated printer tray, perform the following steps:
  1. Open the application being used to print the document. (Example: Microsoft Word)
  2. Click File and click Print.
  3. Verify the paper size.

Verify the Paper Source From the Printing Application Matches the Designated Printer Tray
  1. Open the application being used to print the document.
  2. Click File and click Print.
  3. Verify the paper source.

Do not replace any printer hardware as this is not a printer hardware issue.

Nov 12, 2008 | Dell 3100cn Laser Printer

1 Answer

Print job will not print from the manually feed tray unless I select the Go button for it to process


Table 3-7. Paper Handling Menu
Item Values Explanation
ENVELOPE FEEDER
SIZE=COM10
For supported paper sizes
see page 1-12.
This item appears only when the
optional envelope feeder is installed.
Set the value to correspond with the
envelope size currently loaded in the
envelope feeder.
ENVELOPE FEEDER
TYPE=PLAIN
For supported paper types
see page 1-12.
This item appears only when the
optional envelope feeder is installed.
Set the value to correspond with the
envelope type currently loaded in the
envelope feeder.
TRAY 1 MODE=
FIRST
FIRST
CASSETTE
Determine how the printer will use
Tray 1.
FIRST: If paper is loaded in Tray 1,
the printer will pull paper from that
tray first.
CASSETTE: A paper size must be
assigned to Tray 1 using the
TRAY 1 SIZE option (the next item
in this menu when TRAY 1
MODE=CASSETTE). This allows Tray 1
to be used as a reserved tray.
TRAY 1 SIZE=
LETTER
For supported paper sizes
see page 1-12.
This item appears only when TRAY 1
MODE= CASSETTE. Set the value to
correspond with the paper size
currently

Mar 12, 2008 | HP LaserJet 4350 Printer

2 Answers

Copier will not sort documents correctly


Hi songman to sort you need to have the A4 paper in both cassettes one cassette needs to be A4 portrait(wide edge first) and the other needs to be landscape (short edge first)make sure you have the green paper size selector set correctly as well regards Dr Bob1

Apr 09, 2007 | Ricoh Aficio 1018D Copier

Not finding what you are looking for?
Kyocera FS-4000DN Laser Printer Logo

93 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kyocera Office Equipment & Supplies Experts

Kyocera HP Expert

Level 3 Expert

523 Answers

CheckitRight
CheckitRight

Level 3 Expert

1362 Answers

Henry Gertcher

Level 2 Expert

48 Answers

Are you a Kyocera Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...