Question about Singer CSP1 Iron

3 Answers

My singer magic press 4 iron comes on but the plate will not heat up. I turn it on one day and it just would not heat up.

Posted by on

Ad

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Not sure how tech savvy you are, but the service manual can be downloaded at http://www.parts.singerco.com/CPpartCharts/Presses/MP4.pdf
UNPLUG THE IRON. Figure 7 shows the wiring. Note that the lamp inside the switch is shown incorrectly. It should be on the other side of the switch. Also the 2 wires running down to the fuse are the red wires. The red wires are interchangeable. Use a continuity tester between wire 2 and wire 3 to test the thermostat. Should be open when dial is turned to the left. Closed when dial turned to the right. Also check continuity on the heaters. If everything looks good but it still doesn't work, replace the circuit board.

Posted on Nov 05, 2009

  • scottmercer Feb 16, 2011

    steven882 . . . You're a good man. I'm savvy enough since I have repaired my Singer Magic Press 4 once previously. My problem is I need a new circuit board; my old one is burned out.
    The info on the old board is:
    201762 pc1 WORLDTRONICS WT - 3089 (all on top of board).
    The number "201762" is also on the bottom of the board.
    Can you tell me where I can get a new board?

    Thank you for your courteous attention to my problem, and hopefully a good answer!

    Scott Mercer
    scottmercer@hal-pc.org

×

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My singer magic press 4 was working and when i was about to finish the last garment it did not turn on.

Posted on Jul 22, 2009

  • ushadesaird Jul 27, 2009

    pl tell me where can i get it repaire or if can do it myself,where can i buy the parts thanks.

×

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 136 Answers

Probably need new auto shut off board

Posted on Jun 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I find out why my singer magic press 4 won't work? no light comes on, no heat


Assuming you have tried different power points in the house, it is likely the mains cable plug of the iron is faulty. Worst the cutoff fuse or control inside has tripped. Would suggest if mains cable or plug is ok then buy a new iron as these can be risky to repair without knowing what one is doing.

Aug 26, 2014 | Irons

1 Answer

Singer magic steam press 7


singer magic 7 is used carefully as it is closely to iron so check if wires are connected correctly

Jan 22, 2014 | Singer Electronic Steam Press Iron

1 Answer

I pressed a T-Shirt with old transfer material on it and the transfer is now on my top heating plate of my Singer Presser. How do I get it off without damaging my heating plate? I tried to press an old...


aplicar detergente multiuso no Brasil marca Veja Unilever associado a creme com abrasivo, tipo utilizado por mecanicos para retirada de graxa das mãos, pequena quantidade tomando cuidado com os furos do vapor. atenciosamente. @valefelix

Aug 08, 2011 | Singer Electronic Steam Press Iron

1 Answer

Instruction manualfor csp-1 singer


Located here
http://www.amazon.com/Singer-CSP1-Magic-Steam-Press/dp/B00006IV4K

Jun 25, 2010 | Singer CSP1 Iron

4 Answers

Lost intruction manual Magic Steam Press csp-1


Follow the link or copy it to your browser - http://www.singerco.com/accessories/manuals.html - and search for your Singer.
Kind regards Ryno

Jun 20, 2009 | Singer CSP1 Iron

2 Answers

SINGER MAGIC PRESS 4


I have the singer magic press 4 but the control button is missing can it be replaced

Mar 25, 2009 | Singer Irons

1 Answer

Singer steam press csp-1 iron


Hi,

Here is a tip that will help you to troubleshoot your iron and figure out what is wrong with it.

Electric Iron not Heating Up or not Working Right
http://www.fixya.com/support/r5300202-electric_iron_not_heating_up_or_not

heatman101

Mar 03, 2009 | Singer Electronic Steam Press Iron

Not finding what you are looking for?
Singer CSP1 Iron Logo

Related Topics:

2,293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Singer Irons Experts

Chance Miller

Level 2 Expert

455 Answers

Cindy Wells

Level 3 Expert

5269 Answers

yadayada
yadayada

Level 3 Expert

77544 Answers

Are you a Singer Iron Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...