Question about Office Equipment & Supplies

Open Question

I have a shred safe shredder model wm675xb and I put too much paper in it and now it locked up but reverse still works

Model wm675xb

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: shredder

Check for stuck paper and remove if any. Then check if motor is ok with a multimeter and also main switch.

Posted on May 21, 2007

  • 168 Answers

SOURCE: Shredder suddenly runs only in reverse

Do you hear the motor moving in both directions? I just had the same problem with mine. On mine, you can hear the motor moving in both directions but it would only move the shredder teeth in reverse and the teeth would not move going forward. I took the unit apart and found out that the gear right next to the motor shaft was rounded out in the middle. The solution would be to get a new gear or gears if you can get them. Make sure you inspect all the gears to see if there is a lot of play. You might have to replace more than 1 gear. What I did on mine, was take a brass tubing that was just a little larger than the shaft, drill out the center of the bad gear and press the tubing into the center of the bad gear. This took up the extra play and my Tech Solution TS8000 is working again. Hope this helps. If you have any other questions, feel free to email me at macgyver69@netzero.net

Posted on May 30, 2007

SOURCE: My shredder stop shredding. has paper caught in it

Shredder drive gear is probably shredded - hard part to find or replace usually. Could mean a new shredder;-(

Posted on Sep 08, 2007

otacon
  • 1944 Answers

SOURCE: Shredder suddenly runs only in reverse

Hi,

Did you check out this thread?

http://www.fixya.com/support/t135563-shredder_suddenly_runs_only_in_reverse

Posted on Jan 01, 2008

leroyal
  • 2120 Answers

SOURCE: My Aurora AS1010TX paper shredder

If you want to attemp to take the machine apart, there should be a small spoked wheel called a pulse sensor that runs through U-shaped black device.

Blow this out as well as all electric devices inside.

Posted on Sep 27, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Executive Machines EPS 1200X shredder works in reverse, but does not shred.


there should be a forward/ reverse switch that is used to unjam paper being shredded. check that
if it is automatic then check for paper stuck in the shredder causing the reverse action.

May 12, 2015 | Shredder Office Equipment & Supplies

1 Answer

My Black & Decker Shredder #BD-61 all of a sudden does not work. I used it tonight, but the next time I tried it does not work. The lights come on in both positions, but


On some shredders when both the forward and reverse LEDs are on it can indicate either a jam or a full receiver bag/ container (the area that the shredded paper is fed into).
Try the following steps:
  1. ) unplug the power
  2. ) open up the shredder (see 1 on diagram)
  3. ) empty out all the shredded paper (see 2 on diagram)
  4. ) check that the shredding jaws (both the entrance and exit) are clear of any shredded material (see 3 on diagram)
  5. ) put everything back together
  6. ) plug power cord back in
  7. ) force the shredder into reverse (see 4 on diagram)
25380913-likxhgrg1ylhiwcrdlvnywbu-1-0.jpg
Hopefully you should hear your shredder motor running. If it is switch it to automatic and try shredding again

Jan 24, 2015 | Shredder Office Equipment & Supplies

2 Answers

Why does my shredder keep running indefinitely after the paper has been shredded?


small level that switches on the shredder when you put in sheets, is jammed in the on position by a bit of paper

May 12, 2017 | Office Equipment & Supplies

1 Answer

My royal shredder js1100 will only shred in reverse.


Simple to solve!
Get some longnose pliers or strong tweezers.
Unplug the beast. You do not want to shred your finger nails, or your fingers.
Flip the mechanical part upside down. You will find small pieces of papers near the rollers. Pull them out with tweezers or pliers.
Keep hands out of harm\'s way, plug shredder and make it run in reverse for 1/10 of a second.
Unplug and remove more paper impacted in between rollers.
Repeat last two steps until no paper is seen by the rollers.
Plug and continue shredding your papers

Piece of advice. Do not shred your credit cards in shredder. Scissors are cheaper and do not mess your shredder!

Jan 15, 2014 | Office Equipment & Supplies

1 Answer

Royal 85x paper shredder: The shredder will start to shred but stops shortly after "grabbing" the paper. In order to get it shredding again, I have to put the machine in reverse, remove the...


Sometimes spraying shredder oil on the cutting teeth wil work.

You should shred paper with a light weight machine oil poured on the paper to keep the cutting teeth working freely.

Good luck.

P.S. If this doesn't work then just take the head off and cleanj/lubricate any bearings you find.

Mar 23, 2011 | Royal 85X Shredder

1 Answer

Only runs in reverse


I just had this problem with my shredder. I think the problem started with a bin that was full. Running the shredder in reverse resulted in shredded paper being pulled up into the slot used to feed paper into the shredder. Some of this shredded paper was blocking the little plastic tab that activates the switch when paper is inserted, so the shredder would no longer start when paper was inserted. I emptied the bin and removed the shredded paper from the feed slot, being careful not to break the plastic "sensor" while removing the paper from under it. The shredder works fine now.

Dec 13, 2010 | Fellowes W11C Confetti-Cut Shredder

1 Answer

Runs only in reverse


I just had this problem with my shredder. I think the problem started with a bin that was full. Running the shredder in reverse resulted in shredded paper being pulled up into the slot used to feed paper into the shredder. Some of this shredded paper was blocking the little plastic tab that activates the switch when paper is inserted, so the shredder would no longer start when paper was inserted. I emptied the bin and removed the shredded paper from the feed slot, being careful not to break the plastic "sensor" while removing the paper from under it. The shredder works fine now.

Nov 06, 2010 | Fellowes W11C Confetti-Cut Shredder

1 Answer

When you put paper in it starts to shred for about 1/4 inch then goes to reverse. No jams that I can see. Can run forward and reverse without paper with no problem. Sensor problem?


No mention of make or model however this holds true for all shredders.... especially if its a "cross-cut" shredder; put some shredder oil onto the cutting shafts where you insert the paper this will help get rid of some of the build-up that occurs due to the shredding process...also give the "eyes" in the middle of the "throat" a clan with a soft cloth( unplug the machine first or it will start to run and take your cloth in.) Occasionaly shrd a sheet of paper with some shredder oil poured directly onto the paper..this will help lubricate the cutting blades. Lastly...only shred up to about 70% of the rated cpacity..this will result in fewer jams an longer machine life.

Oct 19, 2010 | OfficeMax 0M96431 Shredder

2 Answers

Tech Solutions shredder


It sounds like you may have a gear with a broken tooth you should contact the manufacturer to get more info. Usually when this is the case it will shred good for only a few revolutions and then reversing backs the gear up to a position that allows it to turn the cutters until it once again reaches the area where tooth is missing.

Mar 11, 2008 | Winsource Tech Solutions TS-4500 Cross-Cut...

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Office Equipment & Supplies Experts

kakima

Level 3 Expert

102366 Answers

k24674

Level 3 Expert

7993 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Are you an Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...