Question about Pride Mobility Products Health & Beauty

Open Question

Wires in connector from back to front half of gogo ultra scooter came loose .need color wire sequence to reinstall boot

Posted by Anonymous on


3 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 692 Answers

SOURCE: need schemitic for wiring on

I have the schematics on my computer in PDF format. If you send me your e-mail I'll send you the printouts that I hope will help E-mail me at

Posted on Aug 20, 2010

  • 2047 Answers

SOURCE: wiring for pride ultra x GoGo .... under the

usually there are tons of wires which are put in these units for diverse purposes. As you stated it could be for the diagnostic computer. Although it could also be for another purpose but most likely one or more sensors on the unit. Usually i would say if the unit does not undergo any malfunction then it is best left alone. What other symptoms does the unit show which you think is caused by the wire?

Posted on May 19, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Troubleshooting code beeps 9 times. battery is charged and the unit is not hot.

hi, okay that a system controller fault however it can also be a loose connection around the controller area, removing the connectors that go into the controller has worked for me, if not it's normally a resistor network inside the controller.

I offer a free testing and repair service ...


Jul 23, 2015 | Pride Mobility Products GoGo Ultra X...

1 Answer

Where does one get the wiring diagram
This illustrated parts breakdown will allow you to follow the wiring harnesses and check and test all the interconnects. This manual will allow you to remove covers and locate parts. Some basic problems can be solved by checking for loose, disconnected, burnt or damaged wiring and connectors. This manual will also give you part numbers. It is best to check with customer service before ordering parts since there are parts changes based on Model and serial number.
Just as a point of reference, most issues for this model can be found in the electronics assembly console, the plugs at the controller and the battery box connections and HIDDEN fuses. B7 page 30 is a good example of a hidden fuse on the battery box that is sometimes burnt out. E3 page 28 is another hidden fuse. Hope this helps.

Mar 26, 2014 | Pride Go-Go Ultra X 3-Wheel Travel Scooter

1 Answer

Wiring diagram on a gogo scooter

The wiring interconnects on these scooter are all modular and the blow up assembly diagrams are all you need to trace the wiring and replace components. Aside from a dealer log in to the manufacturer's website you can go to southwest medical's website and get all the information on the wiring and parts. Hope this helps.
SC40X Go Go Ultra Replacement Parts

Mar 01, 2014 | Pride Mobility Products GoGo Ultra X...

1 Answer

My parents have a Go Go Elite traveler, 3 years old, all of a sudden it takes off and then it starts to hesitate and then takes off again. Please help. Can't find service center in CT.

sounds like a short circuit, check the wiring and connectors, maybe add some insulation tape to conectors and any cable showing the metal wire.

Aug 16, 2013 | Pride Mobility Products GoGo Elite...

1 Answer

Intermittent warning beep and won't move

There is this set of wires that run from the tiller head to the scooter body On most of the newer scooters you must remove this cable to split the scooters front half from the back half. This cable has a bunch of wires and pins at its connection point. You need a VOM meter only $9

Turn the scooter off, disconnect the battery, leave the cable plugged up. With respect to the cable, every wire going in must come out. We want to check the continuity of this cable. To do this take the vom meter set it for the highest ohm setting short the probes zero the meter. Look for wires running to the connector you will see the back side of the pins, put a probe on a backside of the pin , now goto the other side of the cable. probe around those wire, for every wire going into the connector/cable combo there should be a wire running out. These cable get pushed pins the female pins can spread to the point were its intermittent. This cable can often be seen being dragged across the ground they ofter get snagged damaging them

Jun 10, 2012 | Pride Go-Go Ultra X 4-Wheel

1 Answer

Have GOGO scooter, when you turn it on the alarm sounds and will not to anything, it has been fully charged.

Princess try the freewheel lever make sure its in the drive mode and turn the scooter back on Hope this helps

Mar 26, 2011 | Pride Mobility Products GoGo Ultra X...

1 Answer

I have bought a go go scooter which does not have a manual

evilyn Goto click on scooters then find the picture for GoGo Ultra click on the picture and on that page on the right you will find owners manual click on that and download your manual Hope this helps you

Sep 19, 2010 | Activeforever Pride GoGo Ultra 4 Wheel...

1 Answer

Need schemitic for wiring on gogo ultra scooter.can not get power to motor

I have the schematics on my computer in PDF format. If you send me your e-mail I'll send you the printouts that I hope will help E-mail me at

Aug 20, 2010 | Health & Beauty

1 Answer

Just bought my dad a second hand go go 3 wheel elite scooter

Hi Linda. Sometimes if there is a blown fuse or faulty connector on the battery leads, the charger thinks the batteries are charged as the voltage coming out of the charger rises to the high level. Some chargers will cut out if this happens. It is probably not the charger.
Make sure the batteries are plugged in correctly, sometimes during transport they will get knocked and become disconnected.
Also make sure that the battery terminals are not loose where the wires connect to the batteries.
Good luck. Neil.

May 21, 2010 | Pride Mobility Products GoGo Ultra X...

1 Answer

My gogo-ultra will not run. it has been stored


Check the connections between the battery and motor, if the rear come apart check there connections there,

If the connection with the batteries string loaded, rough them up slighty with a wire brush but be gentle and is there freewheel lever right in position for drive.


Oct 24, 2009 | Pride Mobility Products Go Go Ultra X 4...

Not finding what you are looking for?
Health & Beauty Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pride Mobility Products Health & Beauty Experts


Level 2 Expert

280 Answers

Colin Taylor

Level 2 Expert

347 Answers

Robin Hill
Robin Hill

Level 3 Expert

1271 Answers

Are you a Pride Mobility Products Health and Beauty Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides