Question about Kenmore HE2 Plus Front Load Washer

Open Question

F-28 code on a kenmore washer

F-28 code model 110.4751

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Repairman can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Repairman (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: F-28 error code on washer

You need to replace the door switch , and MCU.
usually.

http://www.managemylife.com/mmh/lis_pdf/OWNM/L0704196.pdf
manual link above fro troubleshooting advise.
http://www.appliance411.com/service/repairmanual.shtml


another repair manual. http://fixitnow.com/wp/2005/09/23/whirlpool-duet-kenmore-he3t-washer-repair-manual/ DIY above




Posted on Apr 01, 2010

Ad
blueextc3221
  • 15935 Answers

SOURCE: kenmore he2 plus

F28 is a serial bus error from the CCU (Central Control Unit) to the MCU (Motor Control Unit).

All you need is some Electronics contact cleaner spray and a 1/4 inch socket to remove the top of the machine and the back of the machine.
The CCU is the computer looking box at the top front right hand corner.
Find connector M13, (has red marking on it and only 3 wires) disconnect it by pushing the retainer tab back and pulling gently on the connector.
Spray the contacts of the connector and computer with connector cleaner.
Then re-assemble connector.
The MCU is in the back lower left corner.
Find the connector with 3 wires and red mark, and remove this connector in the same way you did the other, spray it and re-install.
Put the back and top back on.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question

Posted on Sep 11, 2010

TheMobilian
  • 8220 Answers

SOURCE: F 28 error code Kenmore front load washer

F28 Com error between MCU and CCU (central control unit) Broken wire. Check the harness closely between central control and motor control unit. Remove the bottom panel and fish out the tech sheet. Duet manual and more photos HERE0e21d99.jpg

Posted on Oct 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Model # SM 8280867 How old is this model?


6 - 10 years in 2012


Whirlpool Washer Ultimate Care ii - Appliance Repair Forums www.applianceblog.com/.../32099-Whirlpool-Washer-Ultimate-Care-ii
  • LAST UPDATED: 2012-05-28
  • 6 POSTS
  • FIRST POST: 2012-05-28
Whirlpool Washer Ultimate Care ii Model Number: SM 8280867 Brand: Whirlpool Age: 6-10 years Hello, The washer ...

Jan 27, 2016 | Washing Machines

1 Answer

My washing mAchine is broken?


code le = thermal overload protection
let washer stand for 30 minutes then restart
if code persist call for service
page 28 user manual

Sep 27, 2015 | Kenmore Washing Machines

1 Answer

My washer is showing a error code of f-28. What does this mean


The F28 error code in most Kenmore models is a MCU (Motor Control Unit) failure or a wiring issue. You did not include a model number for your washer. Without a complete model number I am unable to supply you with anything other than generic help.

Jan 10, 2011 | Kenmore HE2 Plus Front Load Washer

1 Answer

F 28 error code Kenmore front load washer


F28 Com error between MCU and CCU (central control unit) Broken wire. Check the harness closely between central control and motor control unit. Remove the bottom panel and fish out the tech sheet. Duet manual and more photos HERE0e21d99.jpg

Oct 05, 2010 | Kenmore HE2 Plus Front Load Washer

2 Answers

Error codes


Kenmre HE2 Plus front loader has a F 28 error. Whats the problem and how do I fix it?

Jan 19, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

F-28 code


F28 means your washer is locked and not unlocking. To unlock your washer take the bottom access panel off by removing the 3 bottom screws.
Reach up near the latching assembly & Attached to the door latch is a little plastic pull lever. Pull down on this lever and open the door. Unplug your washer for 60 seconds and plug your washer back in. If the error re-occurs you need to replace your door lock.

Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Jun 28, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Kenmore F-28 error - door locked can't get in


Unplug the machine.
Wait 15 seconds.
Plug machine back in.
Press and hold the Power button until the lights come on.
Press and hold Start.
When you hear a click, press Stop.
Open door.

You still have an F-28 issue but you can at least get your clothes now.

Hope this helps.

Jun 09, 2009 | Kenmore HE2 Plus Front Load Washer

1 Answer

Error code F-28


It may be that the drain pump is not the problem at all. Error Code F-28 on the Kenmore HE2 means that there is a signal error between the Central Control Unit (CCU) and the Motor Control Unit (MCU)

Mar 13, 2009 | Kenmore HE2 Plus Front Load Washer

4 Answers

Fault code F20 on kenmore he2t clothes washer


I have a brand new front loader that never fill with water but shows F20. How can I get this machine to wash clothes?

Dec 29, 2007 | Washing Machines

Not finding what you are looking for?
Kenmore HE2 Plus Front Load Washer Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kenmore Washing Machines Experts

Sal DeAngelo

Level 3 Expert

2508 Answers

fordexpert

Level 3 Expert

5572 Answers

Ed Mac

Level 3 Expert

731 Answers

Are you a Kenmore Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...