Question about Ibanez Music

Open Question

Led light keeps flashing even when the battery is new

Replaced the batteries twice but green light is still blinking even when i'm not tuning or playing

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to an Expert (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1212 Answers

SOURCE: i've changed battery in isys+ pre amp on vintage vec500 and now tuner doesn't work (it is blinking green on note tuner no matter of tune and no note letters showing - blank screen)

Is the battery installed in correct polarity? If so- try rotate it in position to rub through potential corrosion.

Since it has a remote battery, it would not hurt to look at the installation to make sure no wires are broken. Especially the ground wire to the pickup.

It might also be a good idea to apply some contact cleaner to the output plug since it is in the power circuit. Cycle the plug in and out a few times to clean the contacts. Also some contact cleaner to the preamp controls would be useful.

Be aware some lubricants may contain silicone and that can interfere with wood finishes or repairs to the finish in the future.

Posted on Apr 07, 2012

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Sabine zoid z-1000 blinks


More than likely you need a new battery those can be cheaply had if you buy 12 piece tea lights with LEDs they have CR2032 in them that's a lithium battery

Apr 02, 2014 | Sabine Z-3000M Zoid Tuner Metronome

1 Answer

Ibanez Srt preamp issue


try opening it up and pinching the two prongs around the patch cord to tighten it up. My bass was cutting out for a while and giving out no sound till i did that

Jul 27, 2013 | Music

1 Answer

I've changed battery in isys+ pre amp on vintage vec500 and now tuner doesn't work (it is blinking green on note tuner no matter of tune and no note letters showing - blank screen)


Is the battery installed in correct polarity? If so- try rotate it in position to rub through potential corrosion.

Since it has a remote battery, it would not hurt to look at the installation to make sure no wires are broken. Especially the ground wire to the pickup.

It might also be a good idea to apply some contact cleaner to the output plug since it is in the power circuit. Cycle the plug in and out a few times to clean the contacts. Also some contact cleaner to the preamp controls would be useful.

Be aware some lubricants may contain silicone and that can interfere with wood finishes or repairs to the finish in the future.

Apr 06, 2012 | Music

1 Answer

I have a Digitech wammy 4 v pedal the led light are going out i have 3 lights left how can i fix the led light the pedal works fine with out the lights


Check the burned out LEDS with a 3 volt battery- a computer bios battery works well for these.

If they do not light, which is likely, just replace them with similar sized units. You can even change their color too. Measure the voltage at the LED sodler pads to see if it is more than 3 volts, if it is, add a resistor to drop the voltage and limit current to the replacements. Digikey sells them, and they ship around the world http://www.digikey.com or Mouser, Both are based in the US, I am not sure what Mouser's international shipping is. http://www.mouser.com

If there is no voltage at the LED pads, look for bad solder connections, or burned out resistors. If the few remaining LEDs still operate as they should, the level meter chip "should" be okay.

Feb 14, 2012 | Digi-Tech Music

2 Answers

When I turn on my BOSS RC-20XL Loop Station the reverse, tap tempo, write, exit and one shot phase start to blink rapidly and I cannot get them back to normal. Therefore, I am unable to use my loop...


Hi. I had the same problem and fixed it by clearing all the phrases. An explanation of how to do this is below (written by someone else, not me) But, expect your guide beat to now sound like a fuzz instead of a drum. This really sucks and there is apparantly no fix for the guide sound except to send it back to Boss. Good luck.

1. Start by selecting Phrase 1.

(if the 'REVERSE' or 'AUTO START' are lit press them off.)

2. Select 'INST & MIC' by pressing 'MODE'

3. Hold down 'EXIT' and 'AUTO START' together - at the same time, this should light up the green LED for 'LOOP PHASE'

4. Hold down 'WRITE' and 'EXIT' together
then hold 'WRITE' on its own
then 'WRITE' and 'EXIT' together again...as if you were clearing a phrase.

they should light up in red and flash, if not try a combo of section 4.

5. Repeat on all Phrases 1 - 11.

Mar 24, 2011 | Roland BOSS RC-20XL Loop Station Phrase...

1 Answer

Hi, i have a acoustic guitar and i am trying to tune it but i do not know how to use the Matrix Chromatic Tuner SR-1050


Hi
Simply turn the tuner on using the power button. Play an open string note close to the tuner (no more than about 1/2 metre away) - for instance the low E on string 6.
The built in microphone will pick up the sound and, if your guitar is reasonably close to being in tune the led light labelled 'E' will illuminate on the lower scale on the tuner along with one of the three other leds to indicate whether the note is flat (b), in tune (green) or sharp (#).
Due to harmonics any or all of these three leds may flash but it is the one that is on the most that matters.
Adjust the tuning peg until the green is on constantly when you play the string.
Move on to the next string
Note - if the string is more than a semitone sharp or flat a different light may flash (e.g if the low E string is 3/4 of a tone flat the D light will come on).
If you wish to tune your guitar to another instrument that is not at perfect pitch (and perhaps cannot be easily adjusted - like a pipe organ) you can use the calibrate button to adjust the setting of the tuner. This temporary recalibration will be lost when the tuner is turned off.

Mar 01, 2011 | Matrix Auto Chromatic Tuner Sr1050

1 Answer

Is he tuner supposed to light up green when the string is correctly tuned?


Before turning the unit on, press and hold down the calib/batt switch to check the condition of the battery on the battery meter.

Then either plug in your electric guitar to the input side of the AG-6 or if tuning an acoustic guitar without electronics placing the AG-6 near the front of the guitar should work. You will not need to press a button to select which string you are about to tune. The AG-6 will detect it and the corresponding light will turn on when it is tuned within range.

Turn on the AG-6 and start by striking the low E (thickest) string while open. This is the number 6 string or 6E. Slowly turn the guitars low E tuning key untill the red LED below the 6E marking on the AG-6 lights up. Continue stricking the open string and turning the key untill the needle centers on zero and the 6E light remains on.

Repeat this for the open A string untill the 5A light turns on and the needle centers on zero.

Repeat for the remaining four strings, 4D 3G 2B and 1E, being careful not to over tighten and break them.

Tip: It may be a good idea once the low E string is tuned, to tune the rest manually, especially new strings or strings way out of tune. Then tune again using the AG-6 tuner.
.
If installing fresh strings you will probably need to stretch each string and re-tune, possibly several times, before they hold their tuning.

Feb 19, 2011 | Fender AG6 Automatic Guitar Tuner

1 Answer

My tuner shows a green flashing light, the battery is new, even checked it with another one. No matter what i do it just shows a green flashing light. picking the strings for sounds makes no difference at...


Often, the flashing green light indicates that the tuner is NOT receiving a signal and is a warning that the tuner is turned on.

First thing is to check if you have normal output from the guitar from the pickup. If the output is normal, there MAY be a failure in the tuner.

ALSO, just because a battery is new doesn't mean the battery isn't depleted... either try another from a different batch or use a voltmeter to check it. I have seen people chasing their tails due to a brand new bad battery.

When you select the tuner does the audio OUT of the guitar cut off as it is supposed to?

Sep 03, 2010 | Washburn D10sbc Acoustic Guitar

Not finding what you are looking for?
Music Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ibanez Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Wayne Tolonen

Level 3 Expert

394 Answers

cwradio73

Level 3 Expert

1162 Answers

Are you an Ibanez Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...