Question about Briggs & Stratton Gas Pressure Washer 20244

Open Question

Won't Start I have a pressure washer that the pull line will only pull out so far and won't start the engine. I seams to be frozen.

Posted by Anonymous on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: pressure washer hesitates, does not start. Unable

get someone to keep the trigger pulled while you try to start it , its probably got presure trapped between the trigger and the pump.

alternatively turn off the water to the pump, pull the trigger to release any pressure trapped.

start the engine , allow engine to warm up, increase revs on engine then turn on water, should be ok then. Unless you have a problem with the engine that is!

Posted on Jul 21, 2009

  • 316 Answers

SOURCE: Briggs and Stratton pressure washer will not

hello dave, the problem is compression to low,you need 60 to 130 lbs to run engine,check for blown head gasket,or bad rings,or a stuck open valve,hope this helps,,

Posted on Feb 22, 2012

  • 6468 Answers

SOURCE: craftsmen, power washer, 2800 psi, won't start when hot.

when it cuts out check for spark the coil might be bad

Posted on Jun 25, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Won't start


Are you saying that it WONT start or that you cannot pull the rope to get it to start?

May 15, 2013 | Dewalt 3800 PSI Pressure Washer

1 Answer

I have a 89 ford ranger it won't start it acts


What have you checked so far ?
Is it getting spark to the plugs ?
Can you spray starting fluid into the throttle body and get it to start ?
Have you checked fuel pressure at the injectors ?

Jan 18, 2013 | Cars & Trucks

1 Answer

MIne Whirlpool duet is having probloms please help me with it!


see this causes and fix it. God bless you
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.

Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

Line Fuse If the washer won't start the line fuse might have blown.

Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.

Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.

Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.

Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.


10_5_2012_7_02_41_pm.gif

Oct 05, 2012 | Indesit W 123 Front Load Washer

1 Answer

Kenmore Elite Model 110.42926 202 after setting the desired cycle will not start when you push the start button


see this causes and fix it. God bless you
Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.



Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.



Line Fuse If the washer won't start the line fuse might have blown.



Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.



Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.



Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.



Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
10_5_2012_7_06_37_pm.jpg

Oct 05, 2012 | Kenmore Elite 45986 Front Load Washer

1 Answer

I has a Crosley Washing Machine Top Loader. Fill light comes on lid locks then NOthing!


seethis causes and fix it. God bless you
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.
Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this time
Line Fuse If the washer won't start the line fuse might have blown.
Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.
Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.
Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.

Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.

Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the hom
Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.

Oct 02, 2012 | Crosley CCW5294W Top Load Washer

1 Answer

When you push start button nothing happens


see this causes and fix it. God bless you
User Control and Display Board If the washer won't start, the user control and display board may be defective. Check for power to the washer first.

Timer If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.

Line Fuse If the washer won't start the line fuse might have blown.
Thermal Fuse If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.

Line Fuse and Holder If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.

Main Control Board If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.

Door or Lid Latch Assembly If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.
Door Lock Motor and Switch Assembly If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.

Incoming Power Problem If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.

Power Cord If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.

9_29_2012_11_52_17_am.gif

Sep 28, 2012 | Washing Machines

1 Answer

My Kenmore H3T washer will not start. When a specified wash cycle is chosen Time of Cycle is displayed but the light for the cycle only flashes and washer will not start. No error code is displayed.MO


see this causes and fix it. God bless you
If the washer won't start, check to be sure there is power to the electrical outlet for the home. If that is OK, the power cord itself might be defective. This is rare. You can check the power cord with an Ohm meter for continuity.
If the washer won't start check to see if there is power at the electrical outlet which the washer is plugged into. Plug a lamp or radio into the outlet to check it. If the outlet is dead, check the circuit breakers or fuses for the home.
If the washer won't start the door lock assembly should be checked. The door lock can fail either mechanically or electrically. Test any switches on the door lock with an Ohm meter. The switches should have continuity according to their design.
If the washer won't start the lid switch assembly might be defective. This is a very common problem. The lid switch assembly can fail either mechanically or electrically. Test any electrical switches with an Ohm meter for continuity. The switches should have continuity according to their design.
If the washer won't start the main control board might be defective. This is not common. Check other parts and causes first.
If the washer won't start the line fuse might have blown, or the line fuse holder might be damaged and need to be replaced.
If the washer won't start the thermal fuse may have blown. It can be tested for continuity. Watch our fuse testing video for more information.
If the washer won't start the line fuse might have blown.
If the washer won't start the timer might be defective. This part is often misdiagnosed, check other components before replacing this timer.
If the washer won't start, the user control and display board may be defective. Check for power to the washer first.
9_27_2012_11_38_48_pm.png

Sep 27, 2012 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

1 Answer

1993 GMC Jimmy won't throttle up..changed fuel pump...sounds like fuel is running back into tank


Check fuel pressure regulator.Start engine hook fuel gauge to fuel line check pressure ready then pull the vacuum hose of the fuel regulator if pressure rises 5-10 psi then its good.

May 13, 2011 | 1993 GMC Jimmy

2 Answers

New Karcher pressure washer won't start


replace the fuel carburetor filter and, or, your fuel tank filter

Aug 31, 2009 | Karcher 2500 PSI Pressure Washer

Not finding what you are looking for?
Briggs & Stratton Gas Pressure Washer 20244 Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Briggs & Stratton Garden Experts

Phil Walker
Phil Walker

Level 3 Expert

605 Answers

John Trevino

Level 3 Expert

1383 Answers

wadingriver
wadingriver

Level 3 Expert

2069 Answers

Are you a Briggs & Stratton Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...