Question about Leviton Electrical Supplies

1 Answer

LEVITON 7090-BR LAMPHOLDER 3 TERMINALS

HAS 3 TERMINALS WHICH ONES DO I USE

Posted by Anonymous on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

I need to ask you for a bit more information. Ordinarily a socket for a 3-way lamp has two external connections, one of which goes to power (black is the standard color) and one which connects to the neutral wire (white is the standard color). The other wire commonly encountered in house wiring is green, which is a ground connection. Lamps normally do not use a ground. The Levitron web page does not flag this socket to be anything out of the ordinary, but neither do they show the connections.

So please provide any additional information that you can on this socket. Is it meant to hold a single, 3-way incandescent bulb, or is it for a florescent bulb? Is it meant for a special purpose?

Posted on Apr 22, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

If the battery harness for the terminals is corroded with lime calcium and rust and is getting a bad connection after trying to start the car a bunch of times could it send the car into protect


low volts wont harm the starting system
means the alternator is working well
maybe the battery is old

more attention to regular servicing
and checking under the bonnet required

try cleaning the battery terminals
if the connection are that crusty
baking soda and hot water
or replace the battery cable connections with new brass ones

May 19, 2016 | Cars & Trucks

1 Answer

How do I replace the Leviton Bi-Pin on a Linear Fluoresent Lampholder?


Take the end cap off the fixture case - unwire the old socket and reverse the process for installing a new socket.
The little slots on either side of the socket slide onto the fixture case.

Nov 12, 2014 | Leviton 23351 T8 Or T12 Turn-type...

1 Answer

Instructions to replace pull chain for Leviton Plastic Lampholder model 8827CW2


I believe it is cheaper just to replace it then try to get the parts!

You may be able to take it apart and salvage it by using what is leftr of the old pull chain but I am not sure.

Feb 09, 2014 | Leviton Electrical Supplies

1 Answer

Wired in 5224 switch using (1) white wire and (3) black ones and it popped the breaker. I switched the wires and now both toggle switches control same light. The previous switch controlled a light and a...


10-25-12
Copy following link for wiring diagrams for Leviton double switch.
http://waterheatertimer.org/How-to-wire-switches.html#double

Only 3 wires will connect to switch. Not 4

If you blew breaker than you connected Neutral wire to switch.
Neutral wire never connects to switch.

Identify Hot wire.
There is only one Hot wire that carries power to switch box.
This wire connects to one side of device ... which side? ... the side where both screws are bonded together.

Oct 25, 2012 | Leviton Electrical Supplies

2 Answers

95 GMC surburban keeps dying when in low rpm. I replaced the fuel filter and it ran good for a few days, then started crapping out again. I then replaced the spark plugs and wires and it ran great for...


First check for a vacuum leak. Any small loose hoses in the engine compartment? If not, suspect the idle air control valve. I have pasted test procedures for the iac below. Be careful not to confuse the tps with the iac. The tps is centered on the ybro5ttle body. The iac is more on the perimeter. An additional test I do after checking the valve is to plug it back in while it is still off the throttle body and verify that it actuates a little when the key is turned on. It should back up a tad to allow idle air through the passage for starting.

TESTING
Disengage the IAC electrical connector.Using an ohmmeter, measure the resistance between IAC terminals A and B. Next measure the resistance between terminals C and D.Verify that the resistance between both sets of IAC terminals is 20-80 ohms. If the resistance is not as specified, the IAC may be faulty.Measure the resistance between IAC terminals B and C. Next measure the resistance between terminals A and D.Verify that the resistance between both sets of IAC terminals is infinite. If the resistance is not infinite, the IAC may be faulty.Also, with a small mirror, inspect IAC air inlet passage and pintle for debris. Clean as necessary, as this can cause IAC malfunction.


Fig. Fig. 2: Using an ohmmeter, backprobe terminals of the TPS sensor to check for proper resistances



Fig. Fig. 3: The TP sensor and IAC sensor are usually located at the side of the throttle body



Fig. Fig. 4: Idle Air Control (IAC) valve wiring and terminal identification
REMOVAL & INSTALLATION

Disconnect the negative battery cable.Disengage the electrical connection.Remove the IAC valve. On thread-mounted units, use 1 1 / 4 in. (32mm) wrench and on flange-mounted units, remove the screw assemblies.Remove the IAC valve gasket or O-ring and discard it.To install:
Clean the old gasket material from the surface of the throttle body assembly on the thread mounted valve. On the flange-mounted valve clean the surface to ensure proper O-ring sealingInstall the valve with a new gasket or O-ring. Tighten the thread mounted assembly 13 ft. lbs. (18 Nm) and tighten the flange mounted attaching screws to 28 inch. lbs. (3 Nm).Engage the electrical connector to the IAC valve.Connect the negative battery cable.ecd523da-60e9-4928-9b74-9d90b47be2df.gif0996b43f802319fe-tedh1mdkpnm2cwqabpnjpaem-4-2.gif0996b43f802319ff-tedh1mdkpnm2cwqabpnjpaem-4-3.gif0996b43f80219b22-tedh1mdkpnm2cwqabpnjpaem-4-4.gif

0996b43f802319ff-tedh1mdkpnm2cwqabpnjpaem-4-3.gif


0996b43f802319fe-tedh1mdkpnm2cwqabpnjpaem-4-2.gif


ecd523da-60e9-4928-9b74-9d90b47be2df.gif

Jul 21, 2017 | 1995 GMC Suburban

2 Answers

I replaced my old 3way toggle switches with the LEviton 5613 3way lighted rocker switches. Wired exactly the way the older toggle switches were wired. Switches work fine just like the older ones but one...


http://www.leviton.com/OA_HTML/ibeCCtpItmDspRte.jsp?item=4044§ion=10103&minisite=10025
The Leviton page for Leviton 5613 does not have a troubleshoot.
Manual shows simple wiring diagram.
3-way switches will not operate lights if switches are wired incorrectly.
Check your ground wire is connected.
Leviton 5613 series is illuminated.
Check that both switches have 5613 number.
Swap switches and see if problem is inside switch.

Nov 13, 2010 | Leviton 5613-2WSP Grounded Switch

1 Answer

The dimmer switch will turn on and off but wont dim the lights on a chandelier. model 6681-w. tried 2 different ones with the same results.


The Leviton 6681 is a push-button rotary-type incandescent dimmer with 600Watt capacity
559b446.jpeg
If you have incandescent bulbs, the dimmer should work.
If the dimmer has different color wires, try reversing the wires.
If the dimmer replaced a 3-way switch, then this is not the right dimmer.
If you have compact florescent bulbs, you need a dimmer that also dims florescent.

http://www.google.com/products/catalog
Link shows the Leviton 6673 incandescent and florescent dimmer

But you also need dimmable compact florescent bulbs.
http://www.amazon.com/DIMMABLE-COMPACT-FLUORESCENT-LIGHT-SPIRAL/dp/B0014B84ZM

Oct 31, 2010 | Leviton #L11-06681-00I Ivory 600 Watt Push...

1 Answer

Installing an up to date leviton how do i know which wire crosses over to the next? 30A


follow the wires to where they enter the breaker cabinet, the ones coming out of a cable will be a pair, red and black or black and white. If you have a volt meter, turn on one set of switches on the breaker and measure the terminals, the one with 230 volts will be the ones to connect that set of wires to

Sep 04, 2010 | General Electric 40/30Amp 4-pole tandem...

1 Answer

What type of storage card is needed for my MC 7090?


Expansion Slot: User accessible SDIO slot (with secure cover);
accommodates extended cards (with cover removed);
NOTE: terminals with extended cards cannot be
accommodated in the charging cradle and will not be sealed...sandisk is best then toshiba then the rest

Jun 09, 2010 | Symbol MC70

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Leviton Electrical Supplies Experts

 Kenneth
Kenneth

Level 2 Expert

50 Answers

Hippy_dd

Level 2 Expert

112 Answers

jdthefixer

Level 3 Expert

744 Answers

Are you a Leviton Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...