Question about Behringer Europower Pmp5000 Powered Mixer Pmp5000

Open Question

Behringuer europower pmp5000 switches off problem

Switches off problem

Posted by Anonymous on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5603 Answers

SOURCE: My Behringer Europower Pmp5000 Powered Mixer blew

Probably the channel A went. If you are fortunate, the power supply is still OK. There are protection circuits for the speakers, however you MUST use speakers that are rated at over 400 Watts. If you use smaller ones, they can get blown. There is a weakness primarily on insulation for channel A and an arc between layers of a circuit board can wipe out several transistors and a zener diode and sometimes a metering resistor. Once this happens, have unit serviced before using it again as further damage can result.
ALSO PLEASE read my tip I posted on FIXYA regarding a grounding hazard when using Speakon to 1/4 inch speaker cables... essentially the barrel of the 1/4 inch jack of the A channel is the hot lead, NOT the tip for that channel.

Posted on Nov 27, 2010

Ad
  • 5603 Answers

SOURCE: How do i hook up

You use special "insert cables" to insert the EQ into the path from teh mixer to the power amps. Thee cables have three 1/4 inch jacks and are a Wye type cable that connect the TIP of the TRS jack to the TIP of the plug to be plugged into the OUTPUT of the EQ channel. A second cable ties teh RING of the insdert jack into the TIP of a plug that lugs in the INPUT of the EQ. You need two of these special cables for stereo operation.

Posted on May 01, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i connect focusrite to europowered pmp4000


You don't say what item of Focusrite equipment you are trying to connect or for what purpose. Most focusrite stuff has jacks with analog outputs for each channel that can be used into the line ins on the mixer and jack/xlr combos that can be used to take a signal to the focusrite box. Then you get the firewire side for the PC and digital outputs as well which will not be of use with your mixer.

Feb 12, 2014 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

Are behringer pmp5000 220 volt?


Yes, the SMPS handles 100 to 240 at 50 / 60hz there is not a physical switch it is automatic for world wide use.

Aug 05, 2013 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

.necesito un diagrama esquematico para europower MPX 5000


.necesito un diagrama esquematico para europower pmp5000 pmp6000

Jun 29, 2012 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

Europower PMP5000, In the Front Panel there is a Main 1 & Main 2 output, can I connect both to 2 Amplifiers so I have four independent outputs or 2 Stereo outputs? Can I Use these two outputs + mon 1...


Yes, you can use both the main1 and main2. They are independently driven and please note that they are PSUEDO balanced drives... that is the cold side of the balanced line is NOT driven as a complement, but is merely returned to signal ground by a 120 ohm resistor. This CAN cause hum problems or noise pickup depending on the connected equipment and ground loops. Best to run this into amps/speakers thaat have TRUE balanced inputs and also keep the power source the same for all devices.

Nov 01, 2011 | Behringer Europower Pmp5000 Powered Mixer...

2 Answers

PMP Mixers hazard


When using Speakon adapter cables with 1/4 inch plugs, the sleeve of channel A is the hot and not the tip of the plug. Inadvertent shorting of this to ground can blow that channel of the amp.

Oct 10, 2011 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

There are two resistors 310-3 10R on the power supply of the Europower pmp 5000, i need to know if it is 330k or 330om.


The schematic for the power supply does NOT show resistors in the 310-3... Where are these in the circuit... IF THESE happen to be the gate drive resistors for the IGBT's they are 33 ohms. If you have hasd a failure in this area there are other parts that typically get destroyed, including one or both the speedup diodes at the same gates; Here is the complete PMP5000 schematic:

http://elektrotanya.com/behringer_europower-p0569_hca2400_sps1000_dpx_pmp-1280s_5000_sch.pdf/download.html

Scroll down to "get manual" and cliick to download. IGNORE other download links. If you need help restoring the PSU get back to me.

Jul 20, 2011 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

I just both the Europower pmp6000 powerd mixer and Eurolive b215xl speakers and i need help conecting the speaker to the mixer. I will be using it with some mics at a function in an hotel. How do I connect...


use 1/4 inch speaker cables. hook one speaker up to "main 1 R" out and the other to "main 1 L" out. if you have additional main speakers, hook them up the the "main 2" outputs.

look for the "bridge amp mode" switch and move it to the "main L- main R" position.

Nov 06, 2010 | Behringer Europower Pmp5000 Powered Mixer...

1 Answer

How to set up my power mixer?


First thing is to read my tip regarding a speaker polarity hazard of the PMP mixers.

Second thing is to VERIFY speaker cables are properly connected.

If you are using in stereo mode set the slider switch to MAIN L/Main R.

describing all possible configurations is not possible on here, but read your manual with this. If you don't have a manual, download one for free.

Oct 14, 2010 | Behringer Europower Pmp5000 Powered Mixer...

2 Answers

I have a Pmp5000 889406987784 Eurowpower PMP5000 1200-Watt 20-Channel Mixer and Speaker Output A has no output. What has happened?


Usual problem is the Channel A amplifier has burned and blown the switching transistors. Usually an internal board arc occurs and unless very skilled at board work of clearing the burned area and replacing the components you are better to replace the HCA2400 amplifier module... about $160

Sep 19, 2010 | Behringer Europower Pmp5000 Powered Mixer...

Not finding what you are looking for?
Behringer Europower Pmp5000 Powered Mixer Pmp5000 Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Behringer Music Experts

Michial Gueffroy

Level 3 Expert

1138 Answers

Vito Vacirca Jr.

Level 2 Expert

140 Answers

Matthew Spark
Matthew Spark

Level 3 Expert

1066 Answers

Are you a Behringer Music Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...