Question about Pioneer ELite SX-A9 HI-FI Audio Receiver 70W SXA9J SX-A9-J

1 Answer

Pioneer elite sx-a6 keeps going to standby - Pioneer ELite SX-A9 HI-FI Audio Receiver 70W SXA9J SX-A9-J

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 53 Answers

I had a receiver that would shut off when I had the volume too loud. It was caused because the speakers were using too much juice. Does it work with less speakers or at low low volumes? Then this may be the case.

I solved it by getting a different receiver.

if it has nothing to do with volume then check your manual and settings for a auto standby feature that may be just putting the receiver to standby after a set time.

Posted on Apr 14, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My pioneer sx-316 multi channel receiver is off on protected mode what do I do to restart


I read the instructions perhaps slightly differently perhaps. I take the instructions to mean first hold down tone and then hold standby/on key for three seconds. Have you tried doing it as two steps?

1 Switch the receiver into standby.
2 While holding down the TONE button, press and hold the  STANDBY/ON button for about three seconds.
3 When you see 'RESET?' appear in the display, press the ENTER button. OK? shows in the display.
4 Press SETUP to confirm.

Feb 03, 2015 | Pioneer New Original SX316S Remote Control

1 Answer

Why does my pioneer elite pro-ro6u have a red light that says standby instead of blue light which is on??


proubly just the design my kenwood has a red light for standby and goes out when turnd on

Sep 07, 2014 | Pioneer Audio Players & Recorders

1 Answer

Pioneer sx-255r can i connect 6 - 8 ohms


Yes, you can use them but be careful. These are not necessarily robust speakers. If they sound strained, back off.

Mar 07, 2011 | Pioneer SX-255R Receiver

1 Answer

Pioneer vsx-01 receiver, standby light burned out. Button works fine, just no blue light. Pioneer sells a replacement standby button......is this easy to install and will it solve the problem? Do you have...


the light is an ledt they very rarely go bad ..to confirm its bad you must first see that the led is getting power --a voltmeter one end to the frame of the unit and the other to either lead on the led will confirm if its bad or not a typical led will run on or near 3 volts dc... if theres no power at the led than the problem is elsewhere

Aug 30, 2010 | Pioneer Elite® VSX-01TXH 7.1 Channels...

1 Answer

Pioneer Elite. Loud popping sound and picture disappeared


Power supply board is dead.The board where the power a/c cord plug into it.Replace the power supply board.Tries websites like Shopjimmy.com,Ebay.com to buy a refurbish power supply board for the replacement.

May 30, 2010 | Pioneer Elite PRO-1140HD 50 in. Plasma...

1 Answer

My sx-315 pioneer receiver overheated and shut down.


Probably the thermal fuse in the main power transformer. Check for ac on both the primary and secondary of the transformer. If you have 120v ac on the primary when the standby light is off and nothing on the secondary you need a new transformer.

Feb 08, 2009 | Pioneer SX-315

1 Answer

Protection circuit activated.


I can tell you what you will have to do , if you can unsolder and solder components then i can help you fix the problem. but if you cannot do some electronic tests or procedures then it is going to be hard for you and me to get this problem fixed
but if you can then please give a fixya rating so that i can further assist you, any other rating than fixya hurts our score , so for me to continue to help you will have to give this rating , sorry but this is fixyas doing , you can always change it if you are dissatified with my help , thanks

electech

Nov 08, 2008 | Pioneer SX-315

1 Answer

How do i reset my Pioneer SX 316 Surround Sound System. i lost the owners manual.


1. Switch the reciever into standby.
2. While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds.
3. When you see RESET? appear in the display, press the ENTER button. OK shows in the display.
4. Press SETUP to confirm.
OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Aug 08, 2008 | Pioneer Audio Players & Recorders

4 Answers

Owners Manual for a Pioneer SX-315


http://safemanuals.com/user-guide-instructions-owner-manual/PIONEER/SX-315%20-HTP-2500--_E

Oct 31, 2007 | Pioneer SX-315

Not finding what you are looking for?
Pioneer ELite SX-A9 HI-FI Audio Receiver 70W SXA9J SX-A9-J Logo

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pioneer Audio Players & Recorders Experts

 Grubhead
Grubhead

Level 3 Expert

5158 Answers

John
John

Level 2 Expert

509 Answers

T-Comtech Repairs
T-Comtech Repairs

Level 2 Expert

417 Answers

Are you a Pioneer Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...