Question about orbit"" 1"" jar top valve"

1 Answer

Just hooked up (water lines only, no control wiring yet) a 3 station Jar top Manifold. One of the valves is open while the other two are shut. Have taken apart and see not apparent reason for it to be open. Any suggestions?

Posted by on

  • Anthony Barker Apr 15, 2014

    Just found the problem. The manufacturer pre-assembled 3 station manifold had one of the valves installed backwards.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 71 Answers

Make sure the bleeder is closed or solenoid is tight. Sometimes valves just fail without a obvious reason. Suggest purchasing the same jar top valve and rebuilt it using the new diaphragm, spring, bonnet and solenoid. This should correct the problem.

Posted on Apr 24, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toro jar top valve quit working


When I work on a valve in the field we usually just leave the valve body in place and change out the parts from a new unit. As long as the valve body is intact as you have described this should remedy whatever problem you are having. Make certain all wire connections are good and that you are getting 24 - 28 volts to the valve selenoid when the timer has selected that station.

Jun 08, 2014 | Toro 53682/53709 1 Inch In Line Valve/Flow

6 Answers

Whirlpool washer timer


Please check the wiring as you might have not hooked up the connectors for the water valve.

Jul 18, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Each station opens valve #1


Sounds like you have a wire in the MV pin without a Master Valve.

Oct 19, 2012 | Rainbird Rain Bird Esp-6tm Sprinkler Timer

1 Answer

I have a 2 zone water timer and the 'low battery' keeps flashing and the timer is making a sound like it wants to water but it doesn't. I changed the batteries 4 times and even went out and...


you could have a short in the lines that lead to the manifold and its not opening the valves which is causing feedback to the timer, usually the neutral wire since it hooks to all the solenoids at the manifold set up, since the timer wants to send out the signal,, it finally shuts down , but in the mean time is using up all the battery backup , go to the manifolds, and check the wires there, it may even help if you uncap them, trim off the bad sections, and rehook them up.

Jul 03, 2011 | Garden

1 Answer

Po 442 po 455


P0442 - Evaporative Emissions System Leak Detected (Small Leak)

P0455 - Evaporative Emissions System Leak Detected (Gross Leak)

This diagnosis detects leaks in the EVAP purge line using engine intake manifold vacuum. If pressure does not increase, the ECM will check for leaks in the line between the fuel tank and EVAP canister purge volume control solenoid valve under the following vacuum test condition. The vacuum cut valve bypass valve is opened to clear the line between the fuel tank and the EVAP canister purge volume control solenoid valve. The EVAP canister vent control valve will then be closed to shut the EVAP purge line off. The EVAP canister purge volume control solenoid valve is opened to depressurize the EVAP purge line using intake manifold vacuum. After this depressurization is implemented, the EVAP canister purge volume control solenoid valve will be closed.

Causes:
- Missing Fuel cap
- Incorrect fuel filler cap used
- Fuel filler cap remains open or fails to close
- Foreign matter caught in fuel filler cap
- Incorrect fuel tank vacuum relief valve
- Leak is in line between intake manifold

Solutions:
- Re-tighten or replace fuel tank filler cap
- Replace damaged or leaking EVAP canister
- Replace damaged or leaking lines.

Feb 10, 2011 | Chrysler Town and Country Cars & Trucks

1 Answer

How to change bad thermocouple on reliance gas hot waterheater reliance 606


it is important to turn off

the gas supply to the water heater at the manual gas shut-off

valve. This valve is typically located beside the water heater.

Note the position of the shut-off valve in the open/on position

then proceed to turn it off.

2. On the lower front of the water heater locate the combination

gas control valve/thermostat. Depress and hold

the lock tab located under the gas control knob on the right.

Rotate the gas control knob on the combination gas control

valve/thermostat clockwise until "OFF" aligns with the mark on

the front of the gas valve. Once the gas supply has been shutoff,

remove outer door. 3. Using a 1/4" nut driver or socket loosen the two screws securing

the manifold door assembly until they are free. Do not

totally remove the screws and plastic retainer washers from

the manifold door. The screws and retainer washers will be

needed to reattach the manifold door. 4. In this step, the thermocouple, manifold tube, pilot tube and

igniter wire will be disconnected from the combination gas

control valve/thermostat. Using a 7/16" wrench

disconnect the thermocouple (left-hand thread) and pilot tube

(right-hand thread). Using a 3/4" wrench disconnect the manifold

tube (right-hand thread). Carefully pull the igniter wire from

the igniter button.

5. Grasp the manifold tube and push down slightly to free the

manifold tube, pilot tube, and thermocouple from the combination

gas control valve/thermostat. when installation is complete and gas is back on, You should be able to relight the pilot and the functionality of your gas hot water heater should be restored.

Nov 27, 2010 | Reliance Natural Gas Water Heater Control

3 Answers

I replaced timing belt and water pump, car will start, but shuts off when put in gear, had a engine code p1518 p1520 intake runner control fault or stuck open. i need this car to run and stay running while...


you need to make sure that the control solenoid has vacuum and power and ground at the connector, or it will set that code. as long as you did not drop the plenum would should be fine, locate the control solenoid you should be fine

Sep 02, 2010 | 2001 Ford Focus

2 Answers

Icemaker does not make ice wate is connected and on, ice maker runs, arms move to eject ice, but no water ever enters the ice maker.


Hi


Thanks for using FixYa.To start withcheck the water line attached to the back of the refrigerator for good water flow. To do that, first turn off the water supply valve. Then remove the water line from the back of the refrigerator. Next, place the water line into a bucket and momentarily turn the water valve back on to test the flow. If the flow is poor, you need to repair, clean, or replace the tubing or the shut-off valve that supplies the water. If the flow is good, you may have to replace the water inlet valve. If still the issue is not resolved then remove the ice bin, Remove the wires from the auger motor. With the freezer door open and the door switch depressed, push the ice cube release and check for 120VAC between the motor wires. If there is 120VAC then the motor has gone bad. If there is no 120VAC then the control board (module time delay) has to be replaced. Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Jun 03, 2010 | Kenmore 64802 Top Freezer Refrigerator

2 Answers

Won't Fill up on Start, but works when hand filled


water valve located under the unit where the water line connects is either clogged with debris is unplugged, a small clip connects to the top of the valve, or the valve has gone out. The way this valve works is the dishwasher energizes the valve opening it to allow water flow. Once the tub fills to a preset level the valve is disengaged shutting off water flow. Best bet is to take model # and serial # to an appliance parts house and get replacement valve for around 20 u.s.d.
as you will see it is very simple to install.

Hope this has helped you

Dave

Jan 15, 2010 | Dishwashers

1 Answer

Hotpoint washing machine wd860 after 12 - 16 hours there is water in the drum why is this happening


suspect water inlet valve is leaking when in closed position the valve is where the hose's hook up in the back unplug unit from wall to open top use a putty knife to push back small locks located just under top from front does not require much pressure to release top can see with flash light the valve is nomally held in place with two screws part most often has 3 wires 1common to both coils 1 for hot 1for cold if after valve is replaced verify hot and cold not reversed can always just swap hose's if wrong
to verify water coming from inlet valve and not another source can shut off water at wall for the 12 to 16 hours before replacing inlet valve

Dec 10, 2009 | Washing Machines

Not finding what you are looking for?
orbit"" 1"" jar top valve" Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Orbit Garden Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

richie46

Level 3 Expert

12957 Answers

woodzowl307

Level 3 Expert

652 Answers

Are you an Orbit Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...