Question about Panasonic KX-TG1100 Cordless Phone

Open Question

Disconnects after on ring - Panasonic KX-TG1100 Cordless Phone

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

O rings for fuel lines


Actually, the disconnect has TWO o-rings = one to seal it to the tank:

http://i74.photobucket.com/albums/i274/uplandhunter/DSCN0057.jpg

Needed only if there's a leak between the disconnect and the tank.

And one INSIDE the disconnect:

http://i74.photobucket.com/albums/i274/uplandhunter/DSCN0058.jpg

Kinda hard to see in this photo, but look close down inside.
Also, when reconnecting fuel line, put a dab/drop of oil on the male fitting (too hard to do the female fitting, oil doesn't like to run UP-hill).

This will make the fitting go together easier and lube the o-ring to help prevent cutting it.
Also, it helps to oil the o-ring to help install it into the disconnect and the oil left on it will help as mentioned above.

Dec 14, 2013 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

Gas tank reserve valve


Recently, my quick disconnect started to leak...leak pretty profusely actually. Anyway, the Harley dealership tried to sell me an entire new quick disconnect. I insisted that there had to be an o-ring inside the disconnect, but the parts guy swore that there was not. After refusing to spend $58 on a new disconnect, I drained the fuel from the tank, removed the disconnect, and removed the cracked o-ring (the one that the parts guy said did not exist). A quick trip to the local parts store and I found the o-ring for under $1.
Just be sure to ask for one that is fuel resistant.

if I remember correctly, it's the same size o-ring as the oil drainplugs...a #41 I think.

$6.99 for the HELP o-ring kit at your local Advance Auto Parts has the o-ring you need...in fuel grade too.

Dec 10, 2013 | 2011 Harley Davidson FXDB Street Bob

1 Answer

Replace fuel inj 2009 lincoln ls 3.9 eng


Check this procedure about V8 3.9L Fuel Injectors - Removal & Installation
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Relieve fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Engine appearance covers Fuel lines Fuel pressure regulator Fuel cross over elbow Fuel injector connectors Fuel injector clamping plates Fuel injectors
To install:
  1. Install or connect the following:
    Fuel injectors. Use new O-ring seals. Fuel injector clamping plates Fuel injector connectors Fuel cross over elbow Fuel pressure regulator Fuel lines Engine appearance covers Negative battery cable
  2. Start the engine and check for leaks.

  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Disconnect the negative battery cable.
    CAUTION The engine appearance cover is equipped with a noise suppressor. If the noise suppressor becomes separated from the engine appearance cover it must be positioned on the intake manifold prior to installing the engine appearance cover.
  3. Remove the engine appearance cover and the noise suppressor, if detached.
  4. Remove the air cleaner outlet pipe.
  5. Release the fuel system pressure.
  6. Remove the four engine appearance cover mounting bracket nuts and the brackets.
  7. Disconnect the fuel pressure sensor electrical connector from the sensor.
  8. Disconnect the fuel pressure sensor vacuum connector from the sensor.
  9. Disconnect the eight fuel injector electrical connectors from the injectors.
  10. Disconnect the fuel temperature sensor electrical connector from the sensor.
  11. Disconnect the fuel supply tube retaining clip from the fuel injection supply manifold.
  12. Disconnect the fuel supply tube spring lock coupling.
  13. Remove the four bolts and the fuel injection supply manifold and fuel injectors as an assembly.
  14. Remove the fuel injectors from the fuel injection supply manifold.
    CAUTION Use O-ring seals that are made of special fuel-resistant material. Use of ordinary O-ring seals can cause the fuel system to leak. Do not reuse the O-ring seals.
  15. Remove and discard the 16 O-ring seals from the fuel injectors.

    zjlimited_467.jpg

    Fig. Exploded view of the fuel injector mounting-3.9L engine shown

To install:
  1. Lubricate the new fuel injector O-ring seals with clean engine oil before installing.
    CAUTION Use O-ring seals that are made of special fuel-resistant material. Use of ordinary O-rings can cause the fuel system to leak. Do not reuse the O-ring seals.
  2. Install sixteen new O-ring seals onto the fuel injectors. Lubricate the O-ring seals with clean engine oil prior to installation.
  3. Install the fuel injectors and clips onto the fuel rail.
  4. Install the fuel rail and injectors as an assembly. Tighten the fuel rail bolts to 89 inch lbs. (10 Nm).
  5. Install the remaining components in the reverse order of removal.

Keep us updated.

Jan 14, 2011 | 2002 Lincoln LS

1 Answer

How do i install new headlamps


  • Remove the headlight bezel retaining screws. Remove the bezel. If necessary, disconnect the turn signal lamp wires.
  • Remove the retaining ring screws from one or both lights.
  • Remove the retaining rings.
  • Remove the light from the housing. Disconnect the wiring connector from the back of the light.
  • Push the wiring connector onto the prongs at the rear of the new light.
  • Place the new light in the headlight housing. Position it so the embossed number in the light lens is on the top.
  • Place the retaining ring over the light and install the retaining ring screws. Tighten them slightly.
  • Check the aim of the headlight and adjust it, if necessary.
  • Install the headlight bezel. Secure it with the retaining screws.
  • Connect the turn signal lamp wiring (if it was disconnected).
  • Nov 20, 2009 | 1999 Pontiac Grand Am GT

    1 Answer

    My Nokia 6085 rings two-three and then just disconnects.


    try to change the ringtone or ring style. options>set profile>[whatever profile you are using].customize.

    Jan 12, 2009 | Nokia 6085 Cellular Phone

    1 Answer

    Disconnected


    disconnect main inlet and vent hoses. Disconnect the three hoses that goes into the pump at the top. Disconnect wiring harness. Put jack under tank and remove the two straps holding tank in. Once on the ground, blow off all the dust that's around the top. This truck should either be a C style ring or a full ring with tabs. If it's a C style, pull ends together and remove ring. If it's a tab style, grab hammer and screwdriver. Hit each tab to turn the ring counter clockwise. Keep doing this untill it pops off. Remove pump and remeber how it comes out. Put new o ring on new pump and lube ring up with some kind of lubericant. A little oil, tranni fluid, even pertrelum jelly. Pump pump back in, when you push down on it to set it into place, make sure you push it in straight. Not doing this will damage oring and possible fuel leakeage when it's filled. While pressing pump down put old c ring or tab ring back on and get it started. Lock the ring into place and install. Doing everyting in reverse order of what you did to remove.

    Aug 31, 2008 | 1998 Chevrolet C1500

    1 Answer

    Caller Id not working, phone disconnects after 2nd ring


    This problem turned out to be a phone company problem.

    Jun 20, 2008 | Avaya Lands Phones

    2 Answers

    My phone works, but it doesn't ring!


    disconnect all phones and just connect the GE phones.
    there is only a certain amount of power transmited through a phone line to make the phone ring if you have too many phones running off the same line then the ones further away from the main connection suffer

    Jan 05, 2007 | GE 21018GE3 Cordless Phone

    Not finding what you are looking for?
    Panasonic KX-TG1100 Cordless Phone Logo

    Related Topics:

    22 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Panasonic Lands Phones Experts

    kakima

    Level 3 Expert

    102366 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17130 Answers

    guyvstewart

    Level 2 Expert

    85 Answers

    Are you a Panasonic Lands Phone Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...