Question about Ryobi Cultivator

Open Question

Fuel line connector - Ryobi Cultivator

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the fuel line from the intake manifold on a Ford Ranger XLT with a 2.9 Litre engine?


Not sure what you are saying that broke.
If the line is plastic and the fitting has no place for a wrench, you use a tool made to release the spring tension inside the connector. AC lines use the same setup.
If the plastic line is broke, you may be able to get a repair kit at your local auto parts store. The fuel line is designed to be replaced all in one piece, not repaired.

Nov 25, 2015 | Ford Cars & Trucks

1 Answer

How do i remove the fuel delivery and return connectors at the engine


go by the auto parts store, buy fuel line disconnect tools.you take the fuel line disconnect tool, place it on fuel line push tool in the fuel line connector to seperate fuel lines.make sure when you get ready reconnect fuel lines back together you should hear fuel line snap back in place.make sure fuel line in place dont come apart. to be on safe side dont crank car first just turn ignition to the on position for few seconds check for fuel leaks.

Jul 31, 2011 | 2000 Buick Century

1 Answer

Can you explain the steps to change the fuel filter on my 6.5 Diesel GMC Blazer.


Hi, to change the fuel filter, follow the steps below.

Disconnect the negative cable at the battery.

Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.

Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.

Connect the fuel pressure gauge to the Schrader valve.

Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.

Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.

Remove the fuel inlet and outlet lines from the filter following manufacture recommendations (have something around to catch gas that is in the lines and to lay the lines in while prepairing to put new filter on.

To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.

Apply a few drops of clean engine oil to the male tube ends on the filter.

Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.

Then install the filter in the proper direction and leave the mounting bolt slightly loose.

Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the
spring snaps into position.

Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.

Then, do the same with the inlet connector.

Now tighten the filter retaining bolt to the specified torque.

Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter.

Jul 22, 2011 | 1998 GMC Blazer

1 Answer

How do you change the fuel filter on a 96 Olds Cutlass Supreme 4 door 3.1 V6? Vin#1G3WH52M8TF372414


Hi,

Fuel filters are easy to replace but let me give you some friendly warnings:

CAUTION. To reducethe risk of fire and personal injury always follow the correct procedure for disconnecting and connecting fuel pipe quick connect fittings. This will ensure good connections and prevent possible fuel leaks.

CAUTION. Safety glasses must be worn if you use compressed air, as flying dirt prticles may cause eye injury.

Important

The fuel filter is no longer serviced in regular maintenande intervals. It is only necessary to replace the fuel filter in the case of damage or a clogged filter.

Before replacing a fuel filter it is necessary to relieve fuel system pressure.

Your fuel filter is located under the vehicle, driver side, below seating area, front of fuel tank, mounted on frame rail in fuel line




Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.

The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.

Removing a Fuel Filter on an EFI Vehicle


fps23-01.jpg Disconnect the negative cable at the battery.

fps23-02.jpg Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.

fps23-03.jpg Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.

fps23-04.jpg Connect the fuel pressure gauge to the Schrader valve.

fps23-05.jpg Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.

fps23-06.jpg Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.

fps23-07.jpg Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.

fps23-08.jpg Follow the recommended procedures for disconnecting the fuel inlet connector.

fps23-09.jpg Art courtesy of Delmar - Thomson Learning.

Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.

Installing Fuel Filters
In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
  • To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.
  • Apply a few drops of clean engine oil to the male tube ends on the filter.
  • Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.
  • Then install the filter in the proper direction and leave the mounting bolt slightly loose.
  • Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the spring snaps into position.
  • Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.
  • Then, do the same with the inlet connector.
  • Now tighten the filter retaining bolt to the specified torque.
  • Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter.
Have fun and all the best

Ben

May 22, 2011 | 1996 Oldsmobile Cutlass Supreme Coupe

2 Answers

How do i get fuel line off gas tank on 1998 gmc seria


These lines slide on and off, theres a clip inside the connector that locks it on, theres a tool used to slide into connector end to release clips, slide tool in and hold hold in connector and then pull line out, twist and pull, the line may be a little hard to remove so while holding the tool in the connector twist and pull line out.heres a picture of the top of the tank where the lines go on to the fuel module and also the tool i speak of, this set does fuel lines and other lines i put arrows on the fuel line ones, this kit is $9.00, hope this helps.johnjohn2_84.jpgjohnjohn2_85.jpg

Mar 20, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

How do you change the fuel pump? is there a access panel and if so where is it located?


Removal & Installation
To Remove:


  1. Before servicing the vehicle, refer to the precautions at the beginning of
    this section.
  2. Release fuel pressure.
  3. Remove or disconnect the following:

    • The rear seat





      Electrical Connector
      dod_intrpd_fuel__tank_elec_conn.gif



    • The fuel pump electrical connector





      Battery Cable
      dod_intrpd_batt_conn.gif



    • Battery cable

  4. Raise and safely support the vehicle
  5. Remove or disconnect the following:





    Fuel Tank Drain
    dod_intrpd_fuel_tank_drain.gif




    • Fuel from fuel tank





      Stabilizer Bar
      dod_intrpd_stab_bar.gif








      Stabilizer Bar and EVAP Canister
      dod_intrpd_evap_cann.gif



    • The rear stabilizer bar brackets from body
    • Stabilizer bar toward rear of vehicle





      Fuel Filler Tube
      dod_intrpd_filler_tube.gif



    • The fuel filler tube from fuel tank





      Fuel And EVAP Lines
      dod_intrpd_fuel_evap_lines.gif



    • Fuel and EVAP lines

  6. Position transmission jack under fuel tank assembly.
  7. Remove fuel tank straps bolts passenger side first.
  8. Lower fuel tank and remove the purge line and vent line.
  9. Disconnect fuel line from fuel pump module by depressing quick connect
    retainers with thumb and fore finger.
  10. Slide fuel pump module electrical connector lock to unlock.
  11. Disconnect the electrical connection from the fuel pump module, by pushing
    down on connector retainer and pulling connector off of module.





    Fuel Tank Locknut
    dod_intrpd_fuel_tank_tool__nut.gif



  12. Use Special Tool # 6856 to remove fuel pump module locknut.
  13. Remove fuel pump and O-ring seal from tank. Discard old seal.

To Install:


  1. Wipe seal area of tank clean and place a new seal in position in the tank
    opening.





    Fuel Tank Locator
    dod_intrpd_fuel_pump_loctr.gif



  2. Position fuel pump in the tank.

    • Make sure the alignment tabs on the underside of the fuel pump module flange
      sits in the notches on the fuel tank.

  3. Position the locknut over the fuel pump module.
  4. Tighten the locknut using Special Tool # 6856

    • Torque to: 40.5 ft. lbs. (55 Nm)

    CAUTION
    Over tightening the pump lock ring may
    result in a leak.

  5. Position the fuel tank on the transmission stand.
  6. Install or connect the following:

    • Fuel pump electrical connector into hole in the body
    • The purge and vent lines
    • Fuel tank and tank straps
    • The fuel filler tube and tighten the clamp
    • The stabilizer bar and install bolts

  7. Lower vehicle.
  8. Install or connect the following:

    • The fuel pump electrical connector that is in the rear seat
    • The rear seat
    • The battery cable

  9. Fill fuel tank.
  10. Use the DRB or equivalent scan tool to pressurize the fuel system.
  11. Check for leaks.


prev.gif next.gif

Sep 23, 2010 | 1999 Chrysler Concorde

1 Answer

Craftsman Brush Wacker routing of fuel lines Model 358-795200 Was laying in bottom of top mount gas tank


Use new fuel line. There should be two things (besides fuel line) in the fuel tank. The small line has a (1) fuel filter attached and is routed to the lower outlet on the carb. This is the fuel supply line. Make sure there are a few inches of it inside the tank. (say enough to reach other side of tank). The larger line should have a (2) nylon connector inside the tank holding it. The connector stays right at the tank hole. That larger line goes to the closest outlet on the purge bulb. The other fitting on the purge bulb should have a larger line that connects to the upper fitting on the carb.
Feed enough length of fuel line thru tank holes to pull them out where cap is to put on the filter and nylon connector...then pull them back thru. WD-40 will aid in this procedure or any light oil.

Jun 10, 2010 | Craftsman Garden

1 Answer

How to replaced fuel filter on ford f250


Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
Removing a Fuel Filter on an EFI Vehicle
fps23-01.jpg Disconnect the negative cable at the battery.
fps23-02.jpg Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.
fps23-03.jpg Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.
fps23-04.jpg Connect the fuel pressure gauge to the Schrader valve.
fps23-05.jpg Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.
fps23-06.jpg Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.
fps23-07.jpg Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.
fps23-08.jpg Follow the recommended procedures for disconnecting the fuel inlet connector.
fps23-09.jpg Art courtesy of Delmar - Thomson Learning. Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.
Installing Fuel Filters
In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
  • To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.
  • Apply a few drops of clean engine oil to the male tube ends on the filter.
  • Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.
  • Then install the filter in the proper direction and leave the mounting bolt slightly loose.
  • Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the spring snaps into position.
  • Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.
  • Then, do the same with the inlet connector.
  • Now tighten the filter retaining bolt to the specified torque.
  • Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter. NOTE THIS IS FOR A 3/4 TON 5.8L

May 22, 2010 | 1992 Ford F250

1 Answer

Fuel filter replacement for 2001 isuzu rodeo


Under vehicle, passenger side, below seating area, front of fuel tank, mounted on frame in fuel line

Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
Removing a Fuel Filter on an EFI Vehicle
fps23-01.jpg Disconnect the negative cable at the battery.
fps23-02.jpg Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.
fps23-03.jpg Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.
fps23-04.jpg Connect the fuel pressure gauge to the Schrader valve.
fps23-05.jpg Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.
fps23-06.jpg Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.
fps23-07.jpg Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.
fps23-08.jpg Follow the recommended procedures for disconnecting the fuel inlet connector.
fps23-09.jpg Art courtesy of Delmar - Thomson Learning. Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.
Installing Fuel Filters
In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
  • To install a new filter, begin by wiping the male tube ends of the new filter with a clean shop towel.
  • Apply a few drops of clean engine oil to the male tube ends on the filter.
  • Check the quick connectors to be sure the large collar on each connector has rotated back to the original position. The springs must be visible on the inside diameter of each quick connector.
  • Then install the filter in the proper direction and leave the mounting bolt slightly loose.
  • Install the outlet connector onto the filter outlet tube and press the connector firmly in place until the spring snaps into position.
  • Grasp the fuel line and try to pull this line from the filter to be sure the quick connector is locked in place.
  • Then, do the same with the inlet connector.
  • Now tighten the filter retaining bolt to the specified torque.
  • Once everything is connected, lower the vehicle, start the engine, and check for fuel leaks at the filter.

May 15, 2010 | 2001 Isuzu Rodeo

1 Answer

Where do I find the fuel pressure regulator and how to change it on a 2001 hyundai xg300


The fuel pressure regulator is built in to the fuel pump

f89c7c1.gif
Fuel tank and fuel pump assembly—XG 300

  1. Before servicing the vehicle, refer to the Precautions section.
  2. Relieve the fuel system pressure.
  3. Drain the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Fuel supply, return and vapor lines
    • Fuel fill and vent hoses
    • Fuel pump module connector
    • Fuel level sender connector
    • Fuel tank straps
    • Fuel tank
    • Fuel pump module
To install:
  1. Install or connect the following:
    • Fuel pump module and torque the mounting bolts to 12–24 inch lbs. (1–3 Nm)
    • Fuel tank
    • Fuel tank straps
    • Fuel level sender connector
    • Fuel pump module connector
    • Fuel fill and vent hoses
    • Fuel supply, return and vapor lines
    • Negative battery cable
  2. Fill the tank with fuel and check for proper fuel pump operation.

Jan 10, 2010 | 2001 Hyundai XG300

Not finding what you are looking for?
Ryobi Cultivator Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ryobi Garden Experts

Nick Olsen

Level 2 Expert

183 Answers

Rexter1

Level 2 Expert

40 Answers

Roland W VanLue
Roland W VanLue

Level 3 Expert

486 Answers

Are you a Ryobi Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...