Question about Maytag PYE2300AY Electric Dryer

1 Answer

Belt installation for a maytag dryer model# sde305day

I just can remember how to install the belt to the motor and then to the tension pulley. can you help. thanks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

Usally put dryer belt around the drum first
then around motor the tensioner pulley has to to be pulled up when you do this to get the belt around tensioner then you release the tensioner pulley to put tension on belt

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does anybody have a diagram and/or instructions for changing the serpentine belt on a 1998 celica?



REMOVAL & INSTALLATION

See Figures 12, 13, 14, 15 and 16
If a belt must be replaced, the driven unit must be loosened and moved to its extreme loosest position, generally by moving it toward the center of the motor. After removing the old belt, check the pulleys for dirt or built-up material which could affect belt contact. Carefully install the new belt, remembering that it is new and unused - it may appear to be just a little too small to fit over the pulley flanges. Fit the belt over the largest pulley (usually the crankshaft pulley at the bottom center of the motor) first, then work on the smaller one(s). Gentle pressure in the direction of rotation is helpful. Some belts run around a third or idler pulley, which acts as an additional pivot in the belt's path. It may be possible to loosen the idler pulley as well as the main component, making your job much easier. Depending on which belt(s) you are changing, it may be necessary to loosen or remove other interfering belts to get at the one(s) you want.


0900c15280074b92.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 12: On some components a front pulley bolt must be loosened ... .


0900c15280074b93.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 13: ... then the upper bolt so you can ...


0900c15280074b94.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 14: ... lift up and remove the drive belt


0900c15280074b95.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 15: Once the front belt is removed you can access the other belts in need of replacement
When buying replacement belts, remember that the fit is critical according to the length of the belt, the width of the belt, the depth of the belt and the angle or profile of the V shape (always match up old belt with new belt if possible). The belt shape should exactly match the shape of the pulley; belts that are not an exact match can cause noise, slippage and premature failure.
After the new belt is installed, draw tension on it by moving the driven unit away from the motor and tighten its mounting bolts. This is sometimes a three- or four-handed job; you may find an assistant helpful. Make sure that all the bolts you loosened get retightened and that any other loosened belts also have the correct tension. A new belt can be expected to stretch a bit after installation so be prepared to re-adjust your new belt.
After installing a new belt, run the engine for about 5 minutes and then recheck the belt tension.


0900c15280074b96.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 16: Make sure the belt is aligned on the pulley correctly

Oct 26, 2012 | 1998 Toyota Celica

Tip

Maytag Dryer Belt Diagrams and Replacement


Your dryer belt has broken and you have a new belt to install, but you do not know how to route the belt properly. Here are some pictures or diagrams to help you see how the belt needs to go. Of course the belt needs to go around the drum so that is not included.
The important part is the routing around the motor and the tensioner pulley.


For all single belt models use this diagram:

d5cc892.gif



Style: Flat with ribs
Installation Tips: Flat side of belt against drum

on Mar 06, 2010 | Dryers

1 Answer

Replacing belt on whirlpool dryer lgr7646eq3 and i can't figure out where the tensioner pulley goes. the belt is real loose


Hello the pulley goes in the first holes closest to the motor. You have to pull the loop through the pulley and then hook it around the motors small pulley. Here is a basic video on how to replace the belt click this link http://www.youtube.com/watch?v=LxooXQCin8Y If you have any questions message me back and please also remember when our chat has fully concluded to rank how this opinion has helped in your appliance situation it allows me to continue helping others in future situations with similar issues. Thanks I await your reply
Rick

Sep 17, 2011 | Dryers

2 Answers

Need belt diagram for 96 3800 buick riviea


The 1996 Buick Riviera SC has two belts. An inner and an outer belt. The outer belt is for the supercharger and the inner belt is the drive accessory belt. Rotate the tensioner pulley (idler) and remove the outer belt first. The do the same to remove the inner belt. Check all make pulleys and make sure they are free of any debris or oil.

zjlimited_42.png


Install

Route the belt according to the diagram above leaving the tensioner pulley for last and maintaining tension on the belt with your hand. Rotate the tensioner pulley enough to slip the belt on. Inspect your belt and make sure it on correctly before you start to put the outer belt on. Repeat these steps for the outer belt.

Hope this helps (remember to rate and comment this answer).

Jul 02, 2011 | 1996 Buick Riviera

1 Answer

Removeing and installing tensin pully for 2000 nissan altima


Hello,

The tension pulley is mounted onto a semi-flat mounting bracket that is, in turn, mounted at three points, using bolts that also hold the timing chain cover. You have to jack up the bottom of the motor for temporary support and pull the top engine mount in order to get it off. To replace the tension pulley, ensure that You have the proper kit to replace it and follow the steps below:
  1. Make sure You wedge the car after packing it in a garage where You want to remove and install this tension pulley,
  2. Remove the negative terminal on the battery and leave the car for about 15 minutes before working on the car,
  3. Remove passenger side wheel,
  4. Take off the plastic access panel that is low and to the right in the wheel well opening. It has several plastic screws,
  5. You can now see the tensioner pulley and lower belt. Use a 14mm socket on an extension and loosen the bolt on the pulley.
  6. Behind and under the pulley bracket is an adjuster bolt. Loosen that to be able to move the pulley upward and allowing for the belt to come loose and off. This is now a good time to change that lower drive belt. It will now flop right off the AC compressor, tensioner pulley, and crank pulley.
  7. Reassemble in reverse order.
  8. Remember to fix the negative terminal of the battery back on.
Hope this helped. Thank You for using FixYa!!!

Jan 20, 2011 | 2000 Nissan Altima

1 Answer

Belt replacement- broken belt on a lde7600acw, older dryer. belt has been replaced but won't line up properly on idle pulley and motor? It appears maybe the tensioner is not set up rigt, maybe the belt...


Remember, the belt DOES NOT sit in the groove of the drum but about an inch from it in the direction of the front.
Also, the belt sits on the drum with the grooves facing away from the drum, not on the drum, a common mistake. If you have a new Genuine Maytag belt then there is a diagram of how the belt fits onto the tension pulley.

Jul 23, 2017 | Maytag Dryers

1 Answer

I'm trying to hook up the belt which came loose from the drum. While trying to loop it around the motor pulley, the motor pulley came free and I can feel a spring attached to the motor pulley and the...


the idler pulley keeps tension on the belt itself, and is a complete unit,, it slides into a grove,, and once the belt is correctly installed ,, thats what holds it in place, heres a good reply from another question that may help you with pictures
http://www.wikihow.com/Change-a-Clothes-Dryer-Belt

Aug 03, 2010 | Maytag PYE2300AY Electric Dryer

1 Answer

How do i change the water pump on 2004 sonata 4 cylinder?


Hyundai Car 1999-05 - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Accessory drive belts Water pump pulley Timing belt, tensioner and idler pulley Water pump
To install:
  1. Clean all mating surfaces of any residual gasket material.
  2. Install or connect the following:
    Water pump with a new gasket and torque the bolts to 16 ft. lbs. (22 Nm) Tensioner and timing belt and idler pulley Water pump pulley and drive belts Negative battery cable
  3. Fill the cooling system to the proper level.
  4. Start the vehicle, check for leaks and repair if necessary.
c84998b.jpg

Fig. Water pump assembly-1.8L and 2.0L engines

9eb0fb7.jpg

Fig. Exploded view of the water pump assembly and related components-2.0L engines


Hope this help; TY for using Fixya (remember comment and rated this).

Mar 31, 2010 | Hyundai Motor 2004 Sonata

1 Answer

How to replace a serpentine belt in a ford winstars


e

b1513bf.jpg

Fig. Accessory drive belt routing-3.0L engine



21dafdb.jpg

Fig. Accessory serpentine belt routing-3.0L engine


96f660b.jpg

Fig. Accessory serpentine belt routing-3.8L engine


Removal and Installation

2928bae.jpg

Fig. Drive belt tensioner wear indicator marks


2375d13.jpg

Fig. Place a wrench on the drive belt tensioner bolt and rotate the assembly clockwise to relieve belt tension

Using a 15mm wrench attached to the drive belt tensioner pulley, rotate the tensioner clockwise to release the tension. Remove the drive belt from the pulley. When installing the new drive belt, ensure that the drive belt is routed correctly and note the position of the indicator mark on the tensioner.

Hope heled with this; remember rated this help. Good luck.

Nov 12, 2009 | 2000 Ford Windstar

2 Answers

Model: maytag LDE9606ACE reinstall belt


Go to repairclinic.com and click on the "Repair Help" link at the top of the page. On the following page, look for the "Dryer Belt Diagrams" link under the "Special Features" section. Refer to Diagram E for a Maytag dryer. If you have questions, please let me know. I hope this helps you.

Sep 25, 2009 | Dryers

Not finding what you are looking for?
Maytag PYE2300AY Electric Dryer Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dryers Experts

Tim Whalen

Level 3 Expert

3074 Answers

Marvin
Marvin

Level 3 Expert

81342 Answers

Sal De

Level 3 Expert

2699 Answers

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...